TP-Link Community > Tapo Smart Camera > Tapo C200 cannot maintain green light
< Tapo Smart Camera

Tapo C200 cannot maintain green light

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tapo C200 cannot maintain green light

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Tapo C200 cannot maintain green light
Tapo C200 cannot maintain green light
2024-07-04 03:15:52 - last edited 2024-07-12 03:35:38
Model: Tapo C200  
Hardware Version: V3
Firmware Version: 3.20

Hello,

 

Hope anyone could help me.

 

TAPO C200 

CN: 223A3K1009890

MAC:A8-42-A1-92-EC-60

FCCID:2AXJ4C200V2

HVIN: Tapo C200V3

IC: 26583- C200V2

 

I have just installed the camera c200 but upon resetting it could not maintain a blinking green and red light. it is most of the time having a steady red light. i've done camera reset a lot of times but nothing happens. 

 

also, upon clicking the reset button 5 secs i don't hear any voice promt from the camera. when it gain a temporary green light i can hear clicking sound then the light goes back to red.

 

hoping for any advice. thank you

 

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Tapo C200 cannot maintain green light-Solution
2024-07-04 06:26:13 - last edited 2024-07-12 03:35:38

  @Mik014 

Hi,
You can try the following steps if your camera has a solid red light and does not respond to reset.
1. Ensure your router is working.
2. Power off your camera, and move it close to your router, power on it.
3. Wait for 5 minutes, and if the LED is still solid red, press the reset button for 10 seconds and check if you can reset the camera successfully.
If so, you can reconfigure the camera by following the instructions on the Tapo app.

 

If your camera is working, it would be appreciated if you could share your solution.

 

Best Regards

>> Smart Home: Introduction to Common Smart Action Scenarios for Tapo Cameras >> Tapo Camera Day/Night Mode Selection Guide: Best Settings Recommendations for Different Scenarios >> Enhance Your Tapo App Experience: Introduction to Several Practical Features >> Troubleshooting for Tapo Camera's Privacy Mode Automatic Activation
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Tapo C200 cannot maintain green light-Solution
2024-07-04 06:26:13 - last edited 2024-07-12 03:35:38

  @Mik014 

Hi,
You can try the following steps if your camera has a solid red light and does not respond to reset.
1. Ensure your router is working.
2. Power off your camera, and move it close to your router, power on it.
3. Wait for 5 minutes, and if the LED is still solid red, press the reset button for 10 seconds and check if you can reset the camera successfully.
If so, you can reconfigure the camera by following the instructions on the Tapo app.

 

If your camera is working, it would be appreciated if you could share your solution.

 

Best Regards

>> Smart Home: Introduction to Common Smart Action Scenarios for Tapo Cameras >> Tapo Camera Day/Night Mode Selection Guide: Best Settings Recommendations for Different Scenarios >> Enhance Your Tapo App Experience: Introduction to Several Practical Features >> Troubleshooting for Tapo Camera's Privacy Mode Automatic Activation
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 1257

Replies: 1

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.