Official Release Deco X50/X55 V1 1.5.5 Optimize The Overall App Experience / Network stability
This Article applied to:
Deco X50/X55_V1/1.6_1.5.1/1.5.0
Firmware Download Link:
Deco X50_V1/1.6 | 1.5.5_build_20240718 (Official Version) |
Deco X55_V1/1.6 |
1.5.5_build_20240718 (Official Version) |
Update Advice:
1. Please make sure the Deco APP is up-to-date.
2. How to manually update the firmware via web UI- How to Update the Firmware of Deco.
Modifications and Improvement
1. Supported configuring IPv6 during setup.
2. Added the low-power feature.
3. Enhanced the VPN performance.
4. LED schedule feature supported control of individual device LEDs.
5. Improved the overall Deco App experience, especially with the online client list status.
6. Increased networking number.
7. Enhanced the system security.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@Nicosilva86 altough I truely appreciate all the efforts from @David-TP I fully agree that QC in software release s must get a big make-over and upgrade.
Current status of deco X50 is
- Connection Stable;
- App is useless cause of all the errors and false status indications of cliënts
- Copy Link
- Report Inappropriate Content
@David-TP I've been having absolutely horrible network performance, as far as stability is concerned, since upgrading my 3 X50's to firmware 1.5.5, build 20249718, around 2 weeks ago (my auto-upgrade is disabled).
The typical symptoms seem to be bad connectivity between the main router and the satellite nodes, to the point that the satellite nodes start blinking red, and then become green again after ~10-20 seconds.
Obviously, from a client perspective, a ping to the main router's IP will start showing timeouts when this happens...
The nodes have also not changed as far as their physical location is concerned, and pre 1.5.5, I did not have this issue at all and network performance was very good. Or at least, I never noticed anything significant (which can quickly be seen/felt, in streaming or videoconference calls and such).
Thing I've tried, based on reading these forums, which haven't changed anything as far as this issue is concerned:
* Disabled Beamforming
* Upgraded the firmware to 1.5.5, build 20240816 Rel. 73213, beta
* Rebooting everything (even unplugging everything, just in case)
* Rebooting the modem connected to my main router
So, some questions that come to mind...
* Is there any other (beta?) firmware that I could try that might resolve this?
* Is it possible to downgrade from 1.5.5 to a previous 1.5.x version? (I cannot seem to find this? Not sure if there is one?)
* From what I understand, downgrading to 1.4.1 might be a possibility, but I don't exactly have an urge of wiping out all network configs (unless I can save these and re-apply easily somehow?)...
* Any other suggestion on what might be possibly helpful?
Cheers,
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi, Thank you very much for the feedback.
It is suggested to install the latest beta firmware here: Satellite Deco Units Work Well but Display Offline on the Deco APP
Could you please refer to this link to help me submit the Deco APP log:
Are you able to reproduce this issue constantly?
Wait for your reply.
- Copy Link
- Report Inappropriate Content
Hi David,
i've installed the beta version on my deco's x50. Due that there are issues with the presence indications of some clients in the app. Some aren't showing online even though the are connected.
initially I thought that the beta solved this issue, it appears that this isn't the case .
On one deco x50 I have all the network ports in use, accept the deco app shows only one online and connected.
I hope this information helps.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 13409
Replies: 135
Voters 0
No one has voted for it yet.