Solution Deco APP Frequently Showing "0 Online Clients"
This Article Applied to
Deco X50/X55_V1/1.6,V2/2.6
Deco X20/Deco X60 V4/V4.6
Phenomena Description
Occasionally, users might find Deco APP shows 0 clients connected or the online list is almost empty. While these devices appear to be connected to Deco Mesh and actually work well.
Available Solutions
The following beta versions have been confirmed to be effective, and the fixes will be incorporated into the official releases in the future.
| Deco X50/X55_V1/1.6 | 1.6.7_build_20250314_Pre Release |
| Deco X50/X55_V1.2/1.26 | 1.4.5_build_20250108_Beta |
| Deco X20/Deco X60_V4/V4.6 | 1.6.6_build_20250306_Beta |
Update Advice:
1. Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding.
2. How to manually update the firmware via web UI- How to Update the Firmware of Deco.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
not show protocol IEEE8011_MODE_11AC or NG.
Devices connected to x50 1.6.7 => show.
Devices connected to x20 1.6.6 do not show this parameter
- Copy Link
- Report Inappropriate Content
| Deco X20/Deco X60_V4/V4.6 | 1.6.6_build_20250306_Beta |
This firmware is not getting installed. It is showing an error.
- Copy Link
- Report Inappropriate Content
Hi, from the previous discussion record, I see your Deco X60 is V4.2.
The 1.6.6 beta here is for V4.0/V4.6. The latest official firmware for Deco X60 is still 1.3.0 Build 20240830( or 1.4.0 Build 20241212 Rel. 48194, the next official version )
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP This is very confusing. First my LG Dryer dropped from the wifi connection and would not reconnect. Then during the troubleshooting that issue I discovered the Decos show zero clients connected to any of them. (I have a 3 Deco set-up) I'm only beginner/intermediate level at tech so I don't feel comfortable doing a lot of troubleshooting. I research my purchases to keep the tech stuff as simple as possible and I get frustrated when things don't work as they should. I see these posts have been going on for months now. What is happening and when will it get fixed?
Adding edit: the guest network doesn't respond when I attempt to turn it on.
Managing on iPad Pro with iPadOS 18.5 (22F76)
- Copy Link
- Report Inappropriate Content
Sorry, I couldn't figure out how to add multiple images to a single post.
- Copy Link
- Report Inappropriate Content
Also, I feel I should add that the app on my iPhone does show clients connected... although there is no connection speed displayed.
- Copy Link
- Report Inappropriate Content
@MNLisa You have to enable 2.4 GHz WiFi to connect your IoT devices such as Smart Bulb, Smart Switches, LG Dryer etc on that band.
- Copy Link
- Report Inappropriate Content
@ARGamingPK1 Thank you for replying. I understand that, I was showing that both the 2.4 and the 6 ghz both show as offline. I've tried tuning them on but it doesn't work. The slider bar doesn't stay in the on position, it just goes back to the off position.
- Copy Link
- Report Inappropriate Content
@MNLisa You have to do factory reset of your whole Deco system and do the setup again and make sure 2.4 GHz is ON
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community. If you don't want to factory reset the Deco XE5300, I've left a message with a beta firmware.
You can test whether this version helps.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 4
Views: 4781
Replies: 37
Voters 3
