Home Network Community > Wi-Fi Routers > EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
< Wi-Fi Routers

Solution EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2

Solution EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2

SolutionEasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
2025-10-10 07:39:10 - last edited 2025-12-09 09:45:17
Tags: #EasyMesh #Firmware Update #Network Connectivity
Model: Archer AX58  
Hardware Version: V1
Firmware Version: 1.5.2 Build 20250812 rel.38324

This Article Applied to: 

Archer AX58(EU)_V1_1.5.2 Build 20250812

 

Phenomenon:

Some Archer AX58 users have recently reported that updating their Archer AX58(EU)_V1 to 1.5.2 causes their EasyMesh network to become unstable after 8-10 hours of operation. This requires powering off the Archer AX58 and restarting the router to restore the connection.
It was initially reported by DenisG in this thread.

 

Available Solution:

We want you to know that we understand the inconvenience this change may cause. However, our development team quickly identified the cause and provided a beta firmware. This beta firmware has been verified to address this exception. We recommend downloading and testing it:

Model Direct Download Link
Archer AX58(EU)_V1 Archer AX58(EU)_V1_1.5.2 Build20250922(Beta Firmware) 

 

Note: 

 

Please don't hesitate to reply with your experience with the Archer AX58 beta firmware.

If you have any additional feedback on the Archer AX58, please leave a reply here. This includes, but is not limited to:

  • Complete network topology (with the extender model)
  • Specific operational status, etc.

 

Thank you for your patience and cooperation.

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2-Solution
2025-12-09 08:18:45 - last edited 2025-12-09 09:45:17

I have an Archer AX58 as a gateway with a remote powerline adapter TL-WPA8631P (only "receiver") that is connected through EasyMesh via Ethernet cable and serves as a local switch and an access point. After upgrading the firmware on my AX58 to 1.5.2 it started randomly losing ISP connection (with corresponding green LED turning off) and returning error 500 for admin console. Approximately after +/- 8 hours of operation. Now I found this beta build and applied it. Almost 3 days without issues, thank you!

Recommended Solution
  1  
  1  
#4
Options
8 Reply
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
2025-10-28 15:26:52

  @Joseph-TP When will this become an official release ? 

  0  
  0  
#2
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
2025-10-29 06:42:58

Hello @Yolo2049 ,

Thanks for contacting our community.

Please refer to the official website of your region for the specific release time, or keep the Auto Update button turned on to receive new firmware update notifications as soon as possible.

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#3
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2-Solution
2025-12-09 08:18:45 - last edited 2025-12-09 09:45:17

I have an Archer AX58 as a gateway with a remote powerline adapter TL-WPA8631P (only "receiver") that is connected through EasyMesh via Ethernet cable and serves as a local switch and an access point. After upgrading the firmware on my AX58 to 1.5.2 it started randomly losing ISP connection (with corresponding green LED turning off) and returning error 500 for admin console. Approximately after +/- 8 hours of operation. Now I found this beta build and applied it. Almost 3 days without issues, thank you!

Recommended Solution
  1  
  1  
#4
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
2025-12-09 09:45:13

Hello @anton_ua ,

Thank you for your update and sharing, this is great news!wink

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#5
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
a week ago - last edited a week ago

  @Joseph-TP 
Hello its my first post but it have been several mouth that i search something for it to work with my ax58 v1

I have a ax53 as master and two ax58 v1 as satellite, both ax58 are wired connected and have been update to this beta patch because with the firmware 1.4.3 build 20250314 they both having issue that lost the mesh for no reason, now with this update one of my ax58 work perfectly and the other one froze randomly and i have to reboot him manually. 

 

  0  
  0  
#6
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
Thursday

Hello @Martelus ,

Welcome to our community.

 

May I know if your network topology diagram is as follows:

ISP modem—AX53—AX58)))((( client devices

                          └───AX58

(Note: — stands for wired connection,)))((( stands for wireless connection )

 

Is there a switch between the main router and the satellite router? If yes, please remove the switch and connect the satellite router(the frozen one) to main router for comparison.

Please swap the positions of the two AX58s to eliminate the influence of specific positions.

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#7
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
Sunday

  @Joseph-TP 

Sry for the delay, here a screenshot of my setup 
Principale is the AX53 and the two other or AX58 V1
No switch or between the main and the AX58
i still have to swap the two ax58


  0  
  0  
#8
Options
Re:EasyMesh Network Becomes Unstable on Archer AX58 After Updating Firmware to 1.5.2
10 hours ago

Hello @Martelus ,

Have you swapped the two ax58? What is the result?

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More △New Firmware for Archer BE260/Archer BE400 to Support VPN Merge, New ECO Mode, and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
  0  
  0  
#9
Options

Information

Helpful: 0

Views: 777

Replies: 8

Tags

EasyMesh Firmware Update Network Connectivity
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.