[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?

[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?

[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?
[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?
2025-12-18 13:11:55 - last edited 2025-12-25 12:32:38
Model: Archer AX3000  
Hardware Version: V1
Firmware Version: 1.2.2 Build 20241118 rel.63038(4A50)

I have a home server that I would like to expose to the Internet. Due to how my internet plan, I have to set the router's internet connection type to 'v6plus'. After which, I can neither use NAT port forwarding, nor find any way to allow direction connection to my home server using IPv6.

 

I'd be much appreciated if you guys can share if you have encountered this issue before, and how you solved it (if you did). Thank you very much in advanced.

 

0
0
#1
1 Accepted Solution
Re:[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?-Solution
2025-12-25 12:32:34 - last edited 2025-12-25 12:32:38

  @terziyski Thank you very much for your response. I followed the thread you mentioned and successfully found a way to allow inbound IPv6 traffic through the router. I've documented the whole process in the gist below in case someone needs it.

https://gist.github.com/tuananhlai/ff0b6b639cfc2baa537c114aeee27a85

Recommended Solution
1
1
#5
4 Reply
Re:[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?
2025-12-18 21:52:24

  @AndyLai 

 

Follow this thread for more details on your inquiry.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue as a "Recommended Solution". BTC:149wubkkfoLmNDjDbiTxx4ZU8mpcMA5CJt
0
0
#2
Re:[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?
2025-12-18 23:22:07

  @terziyski Thank you for your response. I've double checked the Advanced > IPv6 section, but it doesn't seem like Firewall Rules is available. I have confirmed that I have the latest firmware available.

0
0
#3
Re:[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?
2025-12-20 16:19:58

Hello @AndyLai ,

At present, the connection types of IPv6 mainly include PPPoE, Dynamic IP (SLAAC/DHCPv6), Pass-Through (Bridge), and Static IP.
So far, no news of supporting the firmware version of Archer AX3000 v6 plus has been received. 

v6plus has regional characteristics. Have you consulted local support to see if there is relevant firmware?

For IPv6 configuration, please refer to How to set up an IPv6 Internet connection on the TP-Link Wi-Fi Routers?

 

 

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click Or ☆Recommended Solution if the post/answer helps.
0
0
#4
Re:[tp-link Archer AX3000] How to allow inbound connections on `v6plus` internet connection type?-Solution
2025-12-25 12:32:34 - last edited 2025-12-25 12:32:38

  @terziyski Thank you very much for your response. I followed the thread you mentioned and successfully found a way to allow inbound IPv6 traffic through the router. I've documented the whole process in the gist below in case someone needs it.

https://gist.github.com/tuananhlai/ff0b6b639cfc2baa537c114aeee27a85

Recommended Solution
1
1
#5