Deco X50/X55_V1_1.5.5 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port

Deco X50/X55_V1_1.5.5 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port

195 Reply
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-03-30 10:06:28

  @David-TP 

 

I've found another bug with the 1.5.0 firmware. If you set the Deco's to accespoint mode the DHCP server does not turn off. This will result in a non working internet after a few hours.

 

Is there anyway to downgrade without bricking them? They are now useless to me, and I'm back using my bad ISP WiFi that doesn't cover my house. Regretting the update. 

  2  
  2  
#53
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-03-31 18:45:43

  @Arrows 

Looks like it really is not possible to downgrade the firmware.

 

I have a set of 3 x50 units and all of them are now stuck in recovery mode.

 

Did get the latest beta firmware , but even this one will not flash.

 

Doesn't matter which firmware i try to upload, all give the failed message.

 

Latest beta (from last week) , beta in this forum thread or any of the official eu firmwares.

 

Looks like there is a bug in the recovery page and it will just not accept a valid firmware.

 

They are still within warranty, but this should be fixed..

 

Why have the option for a recovery mode which doesn't work at all ? 

 

  2  
  2  
#54
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-02 09:22:04 - last edited 2024-04-02 09:25:02

@Billmanakos @Its-me-again 

 
Do you have a Sagecom F3896(LG) cable modem? It seems that this modem has issues with his 2.5 Gbps network port. I have one and I have the Deco's connected to the 2.5 Gbps port (because it can, and it might be faster  wink . My ISP had this in investigation, it seems like a firmware bug concerning energy-efficient-ethernet (802.03az). Symptoms are loosing connection, switching to 100 Mbps, no DCHP trough that port. I'm going to try to connect to another port after work and see if that solves the problem (my internet speed is 400/40 so I won't notice it anyway). 
 

 

  0  
  0  
#55
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-02 09:29:09

  @Arrows 

 

Yes, i do have a Sagemcom F3896 modem. but i did not have issues with the port speed.

However, i am using the modem in bridge mode , so the modem doesn`t have to do much anymore.

 

 

  1  
  1  
#56
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-02 18:59:27

Changing the port didn't solved it. The Deco's are changing from green to red and repeating this

  1  
  1  
#57
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-04 17:03:20

  @David-TP 

I have the same issues as the members above, today I experienced 5 small disconnects and connects during my day. So I would love to know if it is possible to get it back to the 1.4.1 version since it was a stable one.

I have sent already the logs of my Deco

FYI I'm running DECO x50 v1


When should we expect to release a new stable version?

  0  
  0  
#58
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-05 17:39:17

  @XManag3r 

Hi,

Try and remove the fixed WAN setting. Leave it as  auto sense.

There were no  disconnections since switched back to auto sense.

 

  0  
  0  
#59
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-05 17:46:25
Currently my setup is as follows: Nokia ONT FTTH TO GIGABIT -> TP-LINK SWITCH UNMANAGED 5 port ->> Switch Gigabit Port 1 to VOIP Gateway & Switch Gigabit Port 2 to Deco X50 v1 port 1->> WAN Auto sensing ->>> PPPoE with VLAN ID 835 ( Greek Providers VLAN Tagging for DATA ) and Priority 0. With this setup there was no disconnections , if I switch on Fixed WAN the disconnections appear again.
  0  
  0  
#60
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-05 17:51:36
Hi @Billmanakos It was already auto sense. I guess i need to switch to fixed WAN PORT and see the results
  0  
  0  
#61
Options
Re:Deco X50/X55_V1_1.5.0 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
2024-04-06 01:40:28

  @David-TP 

 Since upgrading to X50/X55_V1_1.5.0 I can no longer use Open VPN to connect to my internal network.

After doing some troubleshooting I noticed that the Internet connection IP address displayed on the X55 on the mobile App under More->Internet Connection->IP Address is different to the my ISP IP address when I check on fast.com.  This always used to be the same. I also checked the Deco Internet IP Address listed via the WebUI from a PC on LAN under Advanced--> Status --> Internet.

 

When I checked the logs for the Open VPn connection attempt, it is trying to connect to the ISP internet address which is different to my Deco internet address which may be the issue.  I did try Exporting and new Open VPN config file from the Deco App under More --> Advanced --> VPN Server. Opened the VPN profile and clicked on Export.  This made no difference.

Open VPN worked fine up until the new firmware version was installed X50/X55_V1_1.5.0 which looks to be a BETA firmware version.

My questions are:
Any idea as to why the Deco is now showing a different IP under More->Internet Connection->IP Address to the internet address that is assigned by my ISP?  The internet address in the deco used to match what was assigned by my ISP.
Can this version of the firmware be downgraded to the previous version?  


My current firmware version is 
1.5.0 Build 20240311 Rel. 66190 

  1  
  1  
#62
Options