Setup problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Setup problem

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Setup problem
Setup problem
2020-02-19 17:38:32
Model: Archer A6  
Hardware Version:
Firmware Version:

I go through the quick start guide, go to http://tplink, go through all the steps there, and then it says "ops there is a problem connecting to the internet. But my internet connection is fine. I plug the cable that was in the router into a computer and there is a good connection. I have done this twice. I have rebooted the comcast cable modem and rebooted the router. Same problem.

 

When I first turn on the router, the first 4 lights are green, but the 5th light is orange.  

 

I am totally sure I have a good internet connection.

  0      
  0      
#1
Options
10 Reply
Re:Setup problem
2020-02-19 20:50:49
The orange light says "The router’s Internet port is connected, but the internet service is not available." Try using a different Ethernet cable as there may be issue there even though it works for your PC. May be a marginal connector.
  0  
  0  
#2
Options
Re:Setup problem
2020-02-20 02:14:28

@ArcherC8

I tried connecting it directly to the modem with the cable that came with the router.  I still go the amber light.

  0  
  0  
#3
Options
Re:Setup problem
2020-02-20 12:03:26

@tomc 

 

Try the steps in the first post of this thread: https://community.tp-link.com/us/home/forum/topic/150603

 

  0  
  0  
#4
Options
Re:Setup problem
2020-02-20 12:48:42
That cable may be bad. See this post where another poster had an issue with the supplied cable. https://community.tp-link.com/us/home/forum/topic/184814?replyId=394988
  0  
  0  
#5
Options
Re:Setup problem
2020-02-20 16:42:24

@tomc 

I was able to set up another router in exactly the same place using exactly the same cables.   It is a TP-Link N600.  Unless the TP-Link AC1200 is more sensitive, I am going to assume it is defective and return it  to Amazon.  Is  there  any other reason that  I could set up a  TP-Link N600 but have connection problems trying to set up the TP-Link AC1200 in exactly the same place in the network?

  0  
  0  
#6
Options
Re:Setup problem
2020-02-20 16:51:30
I also would return the router as both should work the same.
  0  
  0  
#7
Options
Re:Setup problem
2020-02-20 18:23:30

@tomc 

Thanks for your help

  0  
  0  
#8
Options
Re:Setup problem
2020-02-21 20:50:59

@tomc 

 

Going back to your original issue if the internet light is amber then two things are happening:

 

1. The modem is not recognizing the new router so it is not giving the router a public IP address. Log into the router and look at the WAN or Internet IP, if it is 0.0.0.0 then the modem needs to have the MAC binding reset, the ISP can do that.

 

2. The new router has a IP address from the modem, but needs different DNS servers. You would go into the WAN settings of the router, then assign the primary DNS to be 8.8.8.8 and the secondary to 8.8.4.4

  0  
  0  
#9
Options
Re:Setup problem
2020-02-21 21:03:04
Tony Try calling in. The comcast modems are not compatible with the new TP link routers. Tech service walked me through it by changing a few settings. T
  0  
  0  
#10
Options
Re:Setup problem
2020-02-22 02:39:41 - last edited 2020-02-22 05:38:35

@tomc 

I have already returned the router to amazon.

I appreciate your help, but this seems too complicated.  With the old router I just pluged it in, went to the setup web page, and that did everything for me. 

I am disappointed with TP-Link and will try another brand.  

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 1346

Replies: 10

Related Articles