Home Network Community > DSL Modem Routers > Archer VR2800 failed to connect to Plus Net after firmware upgrade
< DSL Modem Routers

Archer VR2800 failed to connect to Plus Net after firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
1234

Archer VR2800 failed to connect to Plus Net after firmware upgrade

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR2800 failed to connect to Plus Net after firmware upgrade
Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-13 14:50:56 - last edited 2021-04-12 00:58:56
Model: Archer VR2800  
Hardware Version: V1
Firmware Version: ArcherVR2800(EU)_V1_200710

I bought this modem router last week. I was able to connect to my ISP (Plus Net in UK) on ADSL2. I then upgraded to the latest firmware (ArcherVR2800(EU)_V1_200710) after which I was unable to connect. After downgrading to the original firmware I was able to connect again.

 

I am connecting using interface pppoa_0_38_0_d.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade-Solution
2021-03-12 06:33:09 - last edited 2021-04-12 00:58:56

@sjpt4x 

Update;

The latest official firmware for Archer VR2800 and Archer VR900 V3 has already fixed the issue with UK-Plusnet and please do remember to update to the latest firmware:

ArcherVR2800(EU)_V1_201103

https://static.tp-link.com/2020/202012/20201223/Archer_VR2800(EU)V1_201103.zip

ArcherVR900(EU)_V3_210322

https://static.tp-link.com/2021/202103/20210325/Archer_VR900(EU)V3_210322.zip 

 

Thank you very much.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
Recommended Solution
  0  
  0  
#29
Options
35 Reply
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-14 09:14:42 - last edited 2020-08-20 08:34:47

@Libarch 

Good Day,

Thank you very much for your patience.

We might need your help to check the following information:

  1. After the firmware update, please reset the modem and set it up again;
  2. If possible, during the setup, please choose Plusnet_MER_PPPoA from the ISP profile list;

If still no internet, please help us get the following information:

  1. A picture of the status page on the modem;
  3. The system log when there is no internet after set up on the new firmware;

Thank you~

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-14 13:25:13

I have the same issue with a VR900 that I've had for a couple of years. Tried a firmware upgrade from Archer VR900(EU)_V3_170303 to ArcherVR900(EU)_V3_200708 to resolve a couple of issues and then it will not connect to Plusnet. I've tried a factory reset etc on the new firmware but cannot get it to connect so I had to downgrade to an older version again.

  0  
  0  
#3
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-19 19:20:40

@Sunshine, thanks for offer to look at this, but the reason I bought this router was because I'm upgrading to VDSL2, which has now been implemented so I can't check the original connection. In the next day or two I may try the firmware upgrade again to see if there are also problems with VDSL.

  0  
  0  
#4
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-19 19:28:03

@Sunshine also see this post. Looks like the last-but-one firmware is OK, it's the most recent one that causes the problem

  3  
  3  
#5
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-08-30 06:53:43

@Libarch 

Thank you very much for your updateheart!

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#6
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-09-18 20:16:00

I can confirm the same problem connecting to plus.net.

 

Firmware version "Archer VR2800(EU)_V1_170809" works.

 

But version "ArcherVR2800(EU)_V1_200710" does not work.  It negotiates a VDSL2 link, but the PPP session always fails to login.

I manually configure exactly the same VDSL and PPP settings with both firmware versions.

 

 

I also believe the latest firmware for model VR600-v2 (ArcherVR600(EU)_V2_200701) is broken with the same problem.

 

 

Thanks,
Chris.

  0  
  0  
#7
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-09-21 12:54:46

Same problem but with Zen ISP. I never tried downgrading as the time was getting on but it's nice to know I can as it's an expensive doorstop otherwise. I ended up using an older modem/router I have until they sort this out ( I HOPE ).

  0  
  0  
#8
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-09-30 14:43:05
Same problem. Downgraded to previous firmware - all fine again. The latest firmware says 'Beta' once uploaded to the VR2800. Avoid it.
  0  
  0  
#9
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-10-17 20:23:21

Add me to the list of people unable to connect to PlusNet after upgrading the firmware of my Archer VR2800 to ArcherVR2800(EU)_V1_200710. Downgrading to the previous version of the firmware resolved the connection issue.

  0  
  0  
#10
Options
Re:Archer VR2800 failed to connect to Plus Net after firmware upgrade
2020-10-18 17:28:39

@Vardo 

 I queried the problem over 3-4 weeks and still nothing from TP-link, They have forgotten the VR2800 etc for the newer AX range. I shall think about which manufacturer gives true support for my next modem and does not submit a beta firmware to the public.

  0  
  0  
#11
Options
1234

Information

Helpful: 0

Views: 7327

Replies: 35

Related Articles
Archer VR2800 won't connect to Plusnet with latest firmware
3665 1
Failure to set up Archer VR2800
1006 0
Archer VR2800 & Virgin Hub3
1140 0
TP-Link Archer VR2800 unable to connect to new BT Hub2
1885 0
Archer VR2800 router loses power
2927 0
Archer VR2800 5Ghz stops working
5334 3
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.