TP-Link Community > Tapo Smart Hub > H200 does not stop ringing after "closed and triggered" rules
< Tapo Smart Hub

H200 does not stop ringing after "closed and triggered" rules

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

H200 does not stop ringing after "closed and triggered" rules

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
H200 does not stop ringing after "closed and triggered" rules
H200 does not stop ringing after "closed and triggered" rules
2023-08-31 21:08:31 - last edited 2023-09-22 09:19:44
Tags: #Matter
Model: Tapo H200  
Hardware Version: V1
Firmware Version: 1.2.21 Build 20230731 rel. 51223

Hi,

 

I've just bought a H200 Hub and replaced my H100 (worked well like a charm for months). H200 installation was easy.

I repaired my sensors with H200, everything went well.

 

Then I recreated my rules successfully, altough the "closing triggers" does not stop the ringing of the H200 Hub. (I must stop it manually from the app - via the server).

It worked well with H100!

 

Other (non-ringing rules) seems to be OK. But the ringing based rules fail to stop.

 

I can see all 'opening' and 'closing' triggers in the log list... so the function seems to be work on the server side, but

Like this:

22:50:17 Closed and triggered "Door closed" - ringing cannot stop!

22:50:10 Closed and triggered "Door opened" - ringing is OK

 

I suspect this must be a bug.

Is there any solution, recommendation or new firmaware to resolve this issue?

 

Thanks for any help or final resolution!

 

p.s.: I purchased H200 because of its Ethernet (Wired) capability. (Trying to eleminate as much wi-fi connection as I can.)

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:H200 does not stop ringing after "closed and triggered" rules-Solution
2023-09-20 07:22:01 - last edited 2023-09-22 09:19:44

 Update

 

This problem will be solved on the new firmware 1.2.22, which is currently in a staged rollout. Keep an eye on the new firmware notices and update your device in time!

 

Check this Solution to learn more details about this problem: Re:H200 become silent "then" command not working-Solution

▶ CES 2026 Meet TP-Link AI Assistant and More New Products!
Recommended Solution
  0  
  0  
#8
Options
8 Reply
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-01 06:00:17 - last edited 2023-09-01 07:26:48

  @LA1 

 

Can you share the screenshots of your automation settings here (both "Open" and "Close" conditions)? 

 

Please double-check if the Siren Duration of the "Close" rule is set correctly. 

▶ CES 2026 Meet TP-Link AI Assistant and More New Products!
  0  
  0  
#2
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-01 10:04:07

  @Wayne-TP 

 

"Please double-check if the Siren Duration of the "Close" rule is set correctly." : I'm using the "Become Silent" function (it's been working well with H100 for months...)

 

 

But... it fails with H200

H100 always stopped the ringing in ALL CIRCUMSTANCES. Does not matter what triggered it, how long was the duration of the ringing. It has been stopped by H100.

 

I tried ALL COMBINATION of the rules. It takes too long to describe all combos, but the conclusion is the following:

- The CLOSING rule itself is working well. (I tried with other options such as "switch on/off the plug")

- The ringing STOP functions fail. The obvious setting is 'Become Silent' (worked well with H100) but I also tried to switch on the same/other siren voices and set duration to a lesser value than the opening duration value of the same/other sirens. Both fails.

 

Screenshots attached. ('closing' setting is above, 'opening' settings are below)

Thanks!

 

 

  0  
  0  
#3
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-05 10:19:38

  @Larok @LA1 

 

The problem has been reported to the support engineer, i'll update here if there is any progress. Thank you for your attention on this case!

▶ CES 2026 Meet TP-Link AI Assistant and More New Products!
  0  
  0  
#5
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-07 18:35:15

  @Wayne-TP  

 

Thank you!

  1  
  1  
#6
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-12 11:27:54

@Larok @LA1   Good news! Cause of this issue is located and there is new firmware with the fix. If you would like to test it out first, kindly check your private message and reply to me, thanks!

▶ CES 2026 Meet TP-Link AI Assistant and More New Products!
  0  
  0  
#7
Options
Re:H200 does not stop ringing after "closed and triggered" rules-Solution
2023-09-20 07:22:01 - last edited 2023-09-22 09:19:44

 Update

 

This problem will be solved on the new firmware 1.2.22, which is currently in a staged rollout. Keep an eye on the new firmware notices and update your device in time!

 

Check this Solution to learn more details about this problem: Re:H200 become silent "then" command not working-Solution

▶ CES 2026 Meet TP-Link AI Assistant and More New Products!
Recommended Solution
  0  
  0  
#8
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-21 12:52:47
Thank you!
  0  
  0  
#10
Options
Re:H200 does not stop ringing after "closed and triggered" rules
2023-09-24 20:29:08

  @LA1 Hello I have the same issue with HUB H200 in a random conditions the siren is not stopping ringing so need to stop manually from my handset or the people at home must switch it off by plugging out the DC supply.  I try many different settings but it happen again. I have the impression that it happens more when there are many people or cars passing in front of the camera for example when there is a parcel delivery. I'm ina a residential place with very low passage of people or cars. Thanks,  Alfonso 

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 2483

Replies: 11

Tags

Matter
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.