Beta Software Deco M4/S4_V2 Support Connection Preference
This Article applied to
Deco M4_V2_1.5.8
Deco S4_V2_1.5.1
Download Link:
Deco M4_V2 | Deco M4_V2_1.7.0 ( New version updated on 2024.3.7) |
Deco S4_V2 | Deco S4_V2_1.6.1_build_20240328 (updated on 2024.4.19) |
1. Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding.
2. For Deco M4_V2, the firmware downgrade(back to the official 1.5.8 version) needs to be implemented via firmware recovery.
3. For Deco S4_V2, it would revert to the official 1.5.1 directly via web UI.
4. How to update the firmware via web UI.
Firmware Modifications:
Deco M4_V2_1.7.0 |
|
Deco S4_V2_1.5.1 |
|
Please feel free to comment below if you have any issues with these two firmware versions!
Related Articles:
Connection Preference: Customize Your Preferred Signal Source
Understand the Differences Among Deco Firmware Platforms
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@David-TP Can I configure my 2 Deco M4 units to utilize different channels when employing wired backhaul, thus preventing interference? One serves as the main router, and the other acts as a satellite connected via an Ethernet cable.
- Copy Link
- Report Inappropriate Content
Hi, I'm afraid Deco doesn't allow manually selecting the wireless channels. So far, the satellite Mesh units use the same wireless channel as the main unit.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Still u did'nt check my issue regarding ports not open for 5-7 minutes after i reboot my main deco and not getting internet until ports are not coming back
- Copy Link
- Report Inappropriate Content
Tested various miscellaneous ways to make the client " connection preference " settings to stick, but no joy.
Clients will randomly reset their preferences, although they stay connected to whatever deco was selected before they reset.
Btw where does the client " connection preference " settings get saved to exactly ? The mobile deco app ? Or on the deco itself ?
Regards.
- Copy Link
- Report Inappropriate Content
@David-TP what about deco E4,will it support connection preference option? I have M4 v2 2 pack and 1 e4 mixed.after upgrading the deco m4 firmware to beta still there is no connection prefernce option.but if i dont use deco e4 then the connection preference option works.will there be any firmware released for deco e4?
- Copy Link
- Report Inappropriate Content
I just updated all my 3 x M4r V2 to this firmware (from 1.6.2 Build 20240308 Rel. 55841), as I've had serious connection problems. It didn't do much difference, so I decided to factory reset my main Deco. I also isolated the rest of the network, so now it's only ROUTER - DECO with wire, no other devices on the LAN. And all other Decos are powered off.
1. Deco flashing blue, OK
2. New Wifi Deco_57CC visible
3. Deco app cannot find the Deco, even when Deco_57CC manually connected
I tried with PC and Deco_57CC gives me IP of 192.168.68.100 and Deco sits in 192.168.68.1. I can access the Webui, but it only says "Download TP-Link app....".
So is that new firmware preventing that Deco initial setup somehow?
EDIT: This is my other post about connection issues with my Mesh: https://community.tp-link.com/en/home/forum/topic/666110
/ Simo
- Copy Link
- Report Inappropriate Content
Replying to myself:
I managed to connect o my resetted Deco. I shut down Deco & mobile phone few times and lastly disable Mobile Data from phone. No idea which of these made the trick, but now it's back up and running.
* * *
For some reason, when I activated my IoT network with old name & psw for 30 clients or so (mostly ESP, Sonoff, Tuya), the whole network became unstable again. Traffic is quite low from any IoT device, 1-50kbs. Speedtest takes like 10 secs before anything happens and some PING packets get lost. It differs from time to time.
- What could cause this kind of issue?
- Copy Link
- Report Inappropriate Content
@Dhiman1994 Deco E4 (V4) already supports it, no idea about other hardware versions
- Copy Link
- Report Inappropriate Content
@ImtiazAli Mine is V1, so I guess I have to wait...tp link still hasn't confirmed about E4 V1.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 6
Views: 40590
Replies: 233