Official Release Deco X50/X55_V1_1.5.1 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
This Article Applied to
Deco X50/X55_V1_1.4.1
Firmware Modifications
1. Support WireGuard VPN Server/Client.
2. Support built-in easy configuration of NordVPN/Surfshark VPN.
Note: In compliance with local regulations, the Third-party VPN feature may be restricted in specific regions.
3. Add client speed limit under clients' detailed setting page.
4. Support Fixing the WAN port under Deco APP>More>Advanced>WAN Port.
5. Add Scene Priority under QOS.
6. Add Client MAC Identification to improve the accuracy of device detection.
7. Add more device icons in the Deco APP.
Download Link
| Deco X50_V1 | Deco X50_V1_1.5.5- updated 2024.8.12 |
| Deco X55_V1 | Deco X55_V1_1.5.5- updated 2024.8.12 |
Note:
1. *According to the user feedback and our further test, this 1.5.1 version does not support reverting to 1.4.1 via downgrade firmware recovery directly.
-Ever since 1.3.0, the firmware bin file has been over 32MB which passes the maximum file size of the HTTP uboot upgrade tool. So if you want to revert to 1.4.1, please refer to the following suggestions:
- Still run a firmware recovery on one of the satellites Deco X50 first.
- Try to upload an older official version, 1.2.2_Build_230301.zip for example,
- Then update to 1.4.1 from 1.2.2 via web UI.
- If this process works for the satellite Deco X50, We could repeat it on the main Deco later.
2. Please make sure the Deco APP is up-to-date.
3. Some features might not be available when there are other models in the Mesh network.
Configuration Procedure for the Newly-added Features
WireGuard VPN Server& Client
NordVPN/Surfshark VPN
-
NordVPN
-
Surfshark
Client Speed Limit
Manual Selection of the WAN Port
Set Scene Priority under QOS
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, Thank you very much for the feedback.
When mobile devices are disconnected from the Deco APP, did they have no internet access when connecting to Deco?
Like Mrhaggis and wesselkoning mentioned here:
"Zero clients are able to browse the internet, they get IP addresses, show in the client list, just have no access to the internet"
Did a power restart help to temporarily restore the internet connection?
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
Hi, This version is still in the release process and rolled out in waves. I updated the 1.5.1 official firmware download link for Deco X50_V1 in the first post earlier today if you want to manually update the firmware via web UI.
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
Hi again, devices connected to Deco have internet for some time then they loose connection to the internet and can not show LAN devices like printers, for example one iPhone device connected to deco, does not show up in deco app , has internet for some time and can not use the LAN Printer. After power restart the Deco X50 router everything is back to normal, devices show up in deco app, can see each other on LAN and have internet access. Also new devices can join wifi network.
- Copy Link
- Report Inappropriate Content
Hey @David-TP, I'm not sure if it's related to 1.5.1 version, but I noticed that channels are displayed as =0 on the web admin part of the main satellite
- Model : X50 v1
- Firmware : 1.5.1 on all satellites (3)
- Mode : AP
- Only 5Ghz bands are enabled
- Deco app : 3.7.55 (beta program)
I have rebooted all satellites, no change on the UI
However, no issue (internet speed, connectivity, ~10 devices...) at all on my Deco X50s.
- Copy Link
- Report Inappropriate Content
Pixie80 wrote
Hey @David-TP, I'm not sure if it's related to 1.5.1 version, but I noticed that channels are displayed as =0 on the web admin part of the main satellite
- Model : X50 v1
- Firmware : 1.5.1 on all satellites (3)
- Mode : AP
- Only 5Ghz bands are enabled
- Deco app : 3.7.55 (beta program)
I have rebooted all satellites, no change on the UI
However, no issue (internet speed, connectivity, ~10 devices...) at all on my Deco X50s.
@Pixie80 Was the wireless channel displaying correctly before you upgraded the X50 firmware to this 1.5.1 version?
If the internet speed and connectivity are operating as expected, I assume there might be a display issue. We will check.
- Copy Link
- Report Inappropriate Content
@Kevin_Z I also no longer display any clients. A restart only solves the problem for a short time. But they seem to be all connected.
- Copy Link
- Report Inappropriate Content
Hi, thank you for posting in the community.
The same question for you: does this issue occur after you upgraded the Deco X55 to the latest 1.5.1 version?
Can I have the Deco app version, please? Please make sure the Deco App is also up-to-date.
Is the main Deco working as a router or AP? Please follow this guide and send us the app log via the Deco app for further analysis. Please show me the ticket ID number after you submit the email. Thank you very much.
- Copy Link
- Report Inappropriate Content
@Ulbi same problem like mine, after upgrading with the latest firmware , deco app started to lose devices connected and no new devices allowed . Latest firmware update , Router Mode, Deco App version 3.7.55. Currently i've switched to Access point mode because of this problem.
- Copy Link
- Report Inappropriate Content
@Kevin_Z The Deco app version is the 3.7.55 and the firmware version is also the latest with 1.5.1. There is still a Tp-Link 24 port switch in between and an X50 outdoor repeater via Wi-Fi. The 3 x50 Indoor all hang on the Lan.I think I already sent the system protocol the day before yesterday via support.
- Copy Link
- Report Inappropriate Content
@Billmanakos I had that yesterday at times that the router did not allow any new devices. But it worked again after 15-30 minutes.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 29460
Replies: 194
Voters 1
