Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > DECO Access Points Configuration Failure

< Deco

DECO Access Points Configuration Failure

INFO404AK

2024-08-14 18:02:37 - last edited 2024-08-19 09:03:49

Posts: 1

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2024-08-14

DECO Access Points Configuration Failure

2024-08-14 18:02:37 - last edited 2024-08-19 09:03:49

Tags: #Network Connectivity #Deco Ethernet Backhaul #Access Point Mode #Installation

Model: Deco M4 Archer C80

Hardware Version:

Firmware Version:

Hi there.

I recently purchased a 3 Pack of DECO M4R.

I have my Main Router ARCHER C80 connected to a LITEWAVE LS1008G Gigabit Switch.

I have configured the DECOS as APs.

DECO 1 is connected to the Switch

DECO 2 is connected to DECO 1 via Ethernet Back Haul

When I connect DECO 3 to the Switch, my Wifi goes down and DECO 3 Led turns red. When I disconnect DECO 3 from the switch the Wifi starts to work.

DECO 3 connects Wirelessly without any issue, but I want it to be connected wired. I believe this is a network loop.

Am I doing something wrong? What is the correct way to achieve this?

ROUTER <LAN CABLE> SWITCH <LAN CABLE>DECO 1 <LAN CABLE> DECO 2

<LAN CABLE>DECO 3

All Decos as Access Points.

I would really appreciate any advice on this.

Thanks

1 Accepted Solution

David-TP

2024-08-15 06:44:44 - last edited 2024-08-19 09:03:49

Posts: 11762

Helpful: 1602

Solutions: 1028

Stories: 9

Registered: 2020-04-14

Re:DECO Access Points Configuration Failure-Solution

2024-08-15 06:44:44 - last edited 2024-08-19 09:03:49

@INFO404AK

Hi, Thank you very much for the feedback.

Could you please try to disable the "EasyMesh" on the Archer C80 to see whether it helped?

Could you please also help me test whether the following topology works or not:

ROUTER <LAN CABLE> SWITCH <LAN CABLE>DECO 1 <LAN CABLE> DECO 2<LAN CABLE>DECO 3

Wait for your reply and best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco Deco X50/X55_V1_1.6.0 Open for Test! Try to leave a Message if urgent help is required.

Recommended Solution

3 Reply

klipse

LV3

2024-08-14 19:31:13 - last edited 2024-08-14 19:46:52

Posts: 149

Helpful: 88

Solutions: 8

Stories: 0

Registered: 2019-07-08

Re:DECO Access Points Configuration Failure

2024-08-14 19:31:13 - last edited 2024-08-14 19:46:52

@INFO404AK

I tried the same a few months ago with my C80 and 2x Deco M9 plus units with a switch. I also got a network loop so gave up and changed my setup removing the C80.

It could be your switch causing the problem, to rule the switch out connect the 3 Deco's directly to the C80 LAN ports and see if the Deco network works, if it does then its the switch causing the issues, if not then you know its the C80 that could be the issue.

BT Full fibre 500, 2x M9 Plus V2 and 1x X60 V3.2 connected to BT Hub in AP mode.

David-TP

2024-08-15 06:44:44 - last edited 2024-08-19 09:03:49

Posts: 11762

Helpful: 1602

Solutions: 1028

Stories: 9

Registered: 2020-04-14

Re:DECO Access Points Configuration Failure-Solution

2024-08-15 06:44:44 - last edited 2024-08-19 09:03:49

@INFO404AK

Hi, Thank you very much for the feedback.

Could you please try to disable the "EasyMesh" on the Archer C80 to see whether it helped?

Could you please also help me test whether the following topology works or not:

ROUTER <LAN CABLE> SWITCH <LAN CABLE>DECO 1 <LAN CABLE> DECO 2<LAN CABLE>DECO 3

Wait for your reply and best regards.

Deco Monthly Recap- Check What's Currently Going on With Deco Deco X50/X55_V1_1.6.0 Open for Test! Try to leave a Message if urgent help is required.

Information

Helpful: 1

Replies: 3

DECO Access Points Configuration Failure

DECO Access Points Configuration Failure

Information

Voters 1

Tags