Early Access Deco X50_V1_1.6.4 Boosted Network Stability for Smart Home Devices
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
This Article Applied to
Deco X50_V1_1.6.3
Modifications and Bug Fixes
- Fixed the issue that smart home devices frequently disconnect from the network and struggle to reconnect.
- Fixed the issue that mobile clients showed up with incorrect connection type.
- Fixed the issue that Deco APP Frequently displayed "0 Online Clients"
- Fixed the issue of slow internet speed with Zscaler VPN service.
- Improved system stability and security.
Download Link:
| Deco X50_V1 | 1.6.7_build_20250314 (updated 2025.4.7) |
Update Advice:
1. Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding.
2. How to manually update the firmware via web UI- How to Update the Firmware of Deco.
3. The 1.6.4 could revert to the official 1.6.3/1.6.1 directly via web UI.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Same problem here. Did u fixed it?
- Copy Link
- Report Inappropriate Content
The engineers has conducted a test and found out that it was the DoH/DoT settings that was causing the "no internet connection" and not the manual channel selection.
For now, I have turn on DoT, and use DNS mode as default, when Secure Mode is selected, all devices will lose internet connection.
Feedback has been sent to the engineers and they will update once the bug has been fixed. All is well now. Here's hoping Tp Link will release this channel selection to other models and series as well!
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@David-TP Hi David, tell me the email where to send it
- Copy Link
- Report Inappropriate Content
thanks for your reply.
I returned the X50-5g due to the dropped client connections and red LED.
I got the X50 to use the vpn option.
I have sent on the map and log as requested.
- Copy Link
- Report Inappropriate Content
I sent the log via the app.(Ticket#10715847]) And regarding NOIP, I didn't test it on 1.6.1, I needed a backup internet on 1.6.3, the problem appeared
- Copy Link
- Report Inappropriate Content
Hi, Nice to see you again.
Could you please help me submit the Deco APP log as well?
By the way, Did the NoIP DDNS in Hotspot Backup mode work well on 1.6.1?
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Hi. David. After uploading this firmware, all mobile clients disappeared. They were on 1.6.3 .
And there is also an error in 1.6.3 (official firmware) , when you connect a backup channel, through Hotpoint, the DDNS service does not work (No-IP) - it says no connection. When the wired Internet is everything is fine
- Copy Link
- Report Inappropriate Content
Hi, Nice to see you again.
It appears the 1.6.4 doesn't work as well as I expected.
By the way, the last time I received your feedback, it was still about Deco X50-5G.
Can I have some screenshots of your network maps on the Deco APP, such as:
Could you please also help me submit the Deco APP log-How to submit Deco APP log？
I'll check with the engineer to see whether he has other suggestions.
Thanks again and best regards.
- Copy Link
- Report Inappropriate Content
5 attempts and finally got it to upgrade both X50 Decos.
A slight improvement as the devices have reconnected after the upgrade without intervention or powering off.
No disconnections after 4 hours.
CPU is always 100%.
The satellite X50 is either connected with 0 clients, connected with the correct number of clients, or offline.
Client connections are shown incorrectly for wired and wireless.
Connection preference is missing.
The 3 M9-Plus units have stayed online for the 4 hours.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 8
Views: 17184
Replies: 60
Voters 0
No one has voted for it yet.