Early Access Deco BE65/BE65 Pro_1.2.10 New Firmware with Enhanced Stability & Interference Resistance
This Article Applies to:
Deco BE65(US/AU/CA/EU)_V2.0/2.6
Deco BE63(US)_V2.6
Deco BE11000(US)_2.6
Deco BE65 Pro(US/AU/CA/EU))_V1.0/V1.6
Modifications and Enhancements:
- Boosted Mesh Roaming Performance
- Improved Network Performance in High-Interference Environments
- Increased MLO Network Stability
- Optimized IOT Connectivity
Firmware Download Link:
| Deco BE65/BE63/BE11000_V2.0/V2.6 | 1.2.10_build_20251212_Beta |
| Deco BE65 Pro_V1.0/V1.6 | 1.2.10_build_20251218_Beta |
Update Notice:
- Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
- Please make sure the Deco APP is up-to-date.
- How to manually update the firmware via web UI.
As always, we value your feedback. If you happen to encounter any concerns during or after the firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.
- Provide a detailed network layout, including how the devices are connected, WiFi Backhaul or Ethernet Backhaul.
- Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.
Thank you for your continued support and for being part of our community.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
:(
You can try resetting it using the physical button on the back of the Deco; maybe that will work.
- Copy Link
- Report Inappropriate Content
Very good update on my deco be65 v2.
out of curiosity: disabling QoS ( I don't need really, it's only a workaround for bufferbloat problem) , if i run speed test (6 ghz) with iphone 17 pro max download 1.3 gbps / upload 500 (full). With Ipad M2 download 1.0 gbit / upload 173 (poor). Enabling Qos download speed gives results around 900 mbit and upload around 500 (maximum on my profile DL 2.5/ UL 500).
Thanks
- Copy Link
- Report Inappropriate Content
holding the reset button only removes the settings not the firmware.
I have done lots of testing and I believe the update has confused the unit. It believes it is using wireless backhaul but when I removed the network cable from the switch it goes offline which tells me it was using wired backhaul. I think the update has completely disabled the wireless radios because if I do a reset the only way I can add it back in the app is if I connect it directly with a cable. I just ordered a new unit and will be sending the broken on back.
- Copy Link
- Report Inappropriate Content
Yes, I know, I mentioned it so you could try reconnecting the problematic device to the network, either wired or wirelessly, and updating its software.
- Copy Link
- Report Inappropriate Content
I have tried all of the suggestions with no luck. I have been working with TP-Link support directly and they can't seem to figure out what is going on so I have already ordered a new unit which i should get today.
- Copy Link
- Report Inappropriate Content
Received my new unit today and all is working great. Needless to say I will not be updated the new unit to 1.2.10.
- Copy Link
- Report Inappropriate Content
I update the situation. This firmware improves upload problems even if in my opinion there are some problems with wifi 6e devices. I give you results hoping to be useful.
one ssid 2,4, 5 and g ghz. MLO off, channel width 160 mhz. QoS off. FTTH 2,5/500 with ont nokia 2,5 wan port.
iphone 17 pro max (connected 6 ghz): test is ok, DL 1,3 gbit/UL 508
ipad air m2 (supports wifi 6e not 7, connected 6 ghz): DL ok, 1,1 gbit. Upload poor, 210
test ipad air m2 wired through adapter connected via usb c to ipad.. DL 2 gbit / UL 512. Perfect.
Thanks
- Copy Link
- Report Inappropriate Content
Information
Helpful: 4
Views: 5183
Replies: 47
Voters 1
