Beamforming option disappeared in Deco App after adding x20 to network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Beamforming option disappeared in Deco App after adding x20 to network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Beamforming option disappeared in Deco App after adding x20 to network
Beamforming option disappeared in Deco App after adding x20 to network
2023-11-23 09:16:08 - last edited 2023-12-05 08:50:42
Model: Deco X20  
Hardware Version: V3
Firmware Version: 1.1.4 Build 20230824 Rel.63641

Beamforming option disappeared after adding deco x20 to my network.
 

Also the node keeps on disconnecting, please note that the old node that was placed on the same spot isn't disconnecting before.
 

My network consist of the following nodes:

 X55 for the main node

1 x55 for satellite

3 E4 for satellite

1 m5 for satellite

 

 

  0      
  0      
#1
Options
1 Accepted Solution
Re:Beamforming option disappeared in Deco App after adding x20 to network-Solution
2023-12-05 08:50:36 - last edited 2023-12-05 08:50:42

  @evangelr 

@calledan 

Hi, Thank you very much for your update.

After further checking with the engineers, I am afraid I have made a mistake.

The beamforming on Deco X20_V3 is enabled by default and there hasn't been an on/off switch on the Deco APP for Deco X20_V3.

Sincerely sorry for the inconveniene.

Thanks again and best regards.

 

Recommended Solution
  0  
  0  
#6
Options
8 Reply
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-01 11:12:19 - last edited 2023-12-05 08:46:29

  @evangelr 

Hi, Thank you very much for your feedback.

Could you please help me submit the Deco APP log if you were still having this issue?

How to submit Deco APP log

And if you temporarily remove Deco X20 from the Mesh system, will Beamforming show up again on the Deco APP?

Wait for your reply and best regards.

 

  0  
  0  
#2
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-04 20:58:52 - last edited 2023-12-04 21:00:25

  @David-TP I had the same issue with beamforming once I added a X20.  I removed the X20 and it reappeared, when I readded it Beamforming disappeared.

 

  1  
  1  
#3
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-05 03:09:55

  @calledan 

Hi, is your Deco X20 also Deco X20_V3? You could find the hardware version on the bottom label.

Wait for your reply and best regards.

 

  0  
  0  
#4
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-05 03:13:10

Hi  @David-TP 

 

yes, the beamforming function appeared after removing the x20 from the mesh setup.

 

i'll submit the logs later my day.

 

 

  1  
  1  
#5
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network-Solution
2023-12-05 08:50:36 - last edited 2023-12-05 08:50:42

  @evangelr 

@calledan 

Hi, Thank you very much for your update.

After further checking with the engineers, I am afraid I have made a mistake.

The beamforming on Deco X20_V3 is enabled by default and there hasn't been an on/off switch on the Deco APP for Deco X20_V3.

Sincerely sorry for the inconveniene.

Thanks again and best regards.

 

Recommended Solution
  0  
  0  
#6
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-05 14:18:45

  @David-TP 

 

no worries. So since beamforming is active by default in x20, there is no option to enable/disable the function right?

 

one more question does x55 have a functionality to add vpn service?

  0  
  0  
#7
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-07 03:25:53

  @evangelr 

Hi, Yes, both Deco X55 V1(or V1.6 and V1.2(or 1.26) support VPN server/Client.

Deco VPN Configuration Guide

Deco VPN Server/Client Supported List

Best regards.

  0  
  0  
#8
Options
Re:Beamforming option disappeared in Deco App after adding x20 to network
2023-12-07 11:55:31

Make sure that your Deco X20 system is running the latest firmware. You've provided the current firmware version, so check TP-Link's official website for any newer updates. Updating firmware can often address known issues and improve overall system stability. If the Beamforming option disappeared, try resetting the Deco X20 system to default settings or look for an option to reset individual settings. Afterward, reconfigure your network settings and check if the Beamforming option reappears.

  0  
  0  
#9
Options

Information

Helpful: 0

Views: 1128

Replies: 8

Related Articles