Tapo P100 default status ON

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tapo P100 default status ON

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
34 Reply
Re:Tapo P100 default status ON
2021-06-06 05:31:03

@Solla-topee Hey! Today everyone received a software update - the auto power on function was never delivered :(

  0  
  0  
#13
Options
Re:Tapo P100 default status ON
2021-06-18 23:19:15
Really?? When?? I have bought 4 tapo p100 and am very disappointed with function. I think I'm going to have to return them to the store.
  1  
  1  
#14
Options
Re:Tapo P100 default status ON
2021-06-19 08:17:04
Hey! I upgraded to ITEAD Sonoff Basic R2. I put them in a break in the power cable or the power filter wire. It turns out better and more reliable and does not take up 3 sockets in an outlet, as smart sockets do. Try it. Costs only $ 5
  0  
  0  
#15
Options
Re:Tapo P100 default status ON
2021-06-22 15:30:24

@Solla-topee when release?

  0  
  0  
#16
Options
Re:Tapo P100 default status ON-Solution
2021-06-24 01:39:33 - last edited 2021-09-03 07:59:48

Hello everyone,
Thank you for your feedback and patience!  Set the power state of Tapo plug is Now available for some TAPO models.

You could find the latest information about this feature from here: 
[Tapo Plug] Set Default State after Power Failure is Now Available (Tapo P100 V1.2 / P110)
https://community.tp-link.com/en/smart-home/forum/topic/275292


Please leave the Hardware version and Country version (UK/ EU etc.) of your device there if you require the same feature,  we would record your feedback for further evaluation, thank you for your understanding.

Recommended Solution
  0  
  0  
#17
Options
Re:Tapo P100 default status ON
2021-07-21 07:59:51

@Solla-topee Ultimate solution would be if tapo return into it's previous state after power return.

If it was off before then it should stay off, if it was on before then it should turn on again.

 

I'm using 2 Tapos and I wish that one is on by default (boiler), the other depends on current state (light).

 

In this case you will satisfied all people wishes.

Can you do that?

 

  2  
  2  
#18
Options
Re:Tapo P100 default status ON-Solution
2021-07-25 21:00:59 - last edited 2021-08-04 01:29:17

I already received the firmware with this feature, tested and it works! Thanks for earing us Tapo.

 

Firmware version is 1.4.9

Recommended Solution
  0  
  0  
#19
Options
Re:Tapo P100 default status ON
2021-07-30 15:50:30 - last edited 2021-07-30 16:02:05

@Solla-topee 

When this feature(default state) will be available for HW version 1.0?

  0  
  0  
#20
Options
Re:Tapo P100 default status ON
2021-08-15 12:19:51

Just receive 2 tapo P100 today. After update latest firmware 1.3.4, it still remain off after power cut. Useless and keep in drawer. 

  0  
  0  
#21
Options
Re:Tapo P100 default status ON
2021-08-15 12:25:27

@Max1111 

 

You need to update to 1.4.9

  0  
  0  
#22
Options
Related Articles