Tapo C200 - Issues after FW upgrade
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.Tapo C200 - Issues after FW upgrade
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
good morning,
I have 5 Tapo C200 cameras:
1 camera: hardware version 2.0, firmware version 1.1.19
4 cameras: hardware version 1.0, firmware version 1.1.18
Recently the 5 cameras received an automatic update. After the update the cameras became unstable. They are appearing randomically OFF-LINE (1 camera at time, for all the cameras) in the Tapo app on my mobile and if i try to reach them directly (e.g. through VLC at rtsp://userid:pwd@192.168.1.212:554/stream1) I'm not abble to see the stream.
Randomically, after minutes (5-10), they reappear on the TAPO app and the rstp flow is visible on VLC.
It appears randomically 1 camera at time, for all the cameras.
My perception is that after the last FW upgrade the cameras became unstable. The phenomenon never happened with other FW.
Did you notice anything similar for your cameras?
I tried to reset and reconfigure the cameras but the issue continues to appear randomically.
thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Solved the issue.
Through the TP-LINK support I was able to downgrade the fw on my 5 Tapo C200 cameras. The system started to work again fine. As it worked before the last fw upgrade.
thanks
- Copy Link
- Report Inappropriate Content
Hello @Talb
Thank you for reporting the case with case details.
May I know do you use RTSP streaming 24/7 on the camera? If so, it is recommended to run one RTSP or ONVIF software at a time instead of multiple third party software.
To look into it further, can I have some case details :
- Please enable diagnose mode camera, reproduce the issue and help collect the camera log How to Get the Log of Tapo Camera
- When the camera becomes offline in the Tapo APP, how about the LED status on is it Red or solid Green? Or does the camera still show up router network client list or receive an IP from router. Can you ping the camera IP address at that time (this is to see if camera is accessible in the local network)
- the MAC address of a camera which experiences the issue & your TP-Link ID email account ( please share via PM)
Thanks a lot for helping collecting information to solve the case.
- Copy Link
- Report Inappropriate Content
hi Solla,
answering to your questions:
1. I use RTSP streaming 24/7 on the camera. But, yes, I run one RTSP or ONVIF software at a time. Anyway nothing changed in my usage of the camera, their behaviour changed after fw upgrade. A question: is there the possibility to go back to the previous fw version. It was fine for my cameras.
2. I enabled diagnose mode. It is asking for an SD card. I have only an SD card and 5 five cameras with the issue. I will monitor only for one of them.
3. When the camera becomes offline in the Tapo APP:
-LED status is solid Green,
- the camera still show up router network client list and receive an IP from router,
- ping is KO (the camera didn't answer).
4. MAC address and my TP-Link ID email account to be sent via PM
thanks bye
- Copy Link
- Report Inappropriate Content
Hi Solla,
I tried to upload the file, but it' not possible (receiving msg "Failed to upload." ).
I tried to enclose the content in tjhis post, but it's not possible.(receiving msg "Content or title contains illegal external links")
Please tell me how to do.
I'm sending all the other info via private msg.
thanks.
Please tell me if possible to downgrade the firrmware to the previous version.. The previuous version didn't have issue. Currently my cameras (5) are not useful. I have to waste them.
thanks
- Copy Link
- Report Inappropriate Content
Hello @Talb
Thanks for providing all the case details, there isn't a way that I' aware of to downgrade the firmware for C200, but our senior engineer might be able to help with your case.
To better assist with your case, we created a support email TKID220907828 for your case and get it escalated, please check your email inbox.
Please attach the camera log file in that email. Btw, may I know the issue is only Live-streaming, or the camera shows offline in the APP? Thanks.
- Copy Link
- Report Inappropriate Content
Hi Solla,
I didn't receive any email. My expectation for a fast solution was a FW downgrade. To much time for your R&D departmet to analyze and solve. My mistake to adopt so cheap cameras, ruined by a FW update, for my 7x24 surveillance system.
What I find incredible: in the FW notes it was written "to increase stability", my mistake to accept the update. My system was already stable.
Anyway I didn't receive any email.
- Copy Link
- Report Inappropriate Content
Hello @Talb
I will send another email in that support email TKID220907828 , please check in the spam/trash box as well.
Please check my PM as well.
- Copy Link
- Report Inappropriate Content
Hi Solla-topee,
received the mail and sent the diagnose file.
Added in the mail additional info that could be interesting to debug the issue.
thanks
- Copy Link
- Report Inappropriate Content
@Talb Thanks a lot for the log.
I escalated the case through that support email, kindly wait for the email later.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Solved the issue.
Through the TP-LINK support I was able to downgrade the fw on my 5 Tapo C200 cameras. The system started to work again fine. As it worked before the last fw upgrade.
thanks
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1745
Replies: 14
Voters 0
No one has voted for it yet.