Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )

Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )

Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
a week ago - last edited a week ago

Hi everyone,

I would like to install a Wi-Fi mesh network that covers most of the inside of the house and, eventually, outside.

The house is a traditional old Spanish farm house and the external walls plus most of the internal walls are very thick.

Downstairs is approximately 280m² and upstairs approximately 160m².

The ISP is StarLink giving an internet connection of about 400Mbps via a Gen. 3 router - I am more than happy to put this into bypass mode.

Currently the StarLink router is in the entrace hallway and there are no plans (no need) to change this.

From here I have 3 x Ethernet cat. 6 cables that feed the lounge, main bedroom and the kitchen.

My idea is to put a Deco in the hallway as the master router and a satellite Deco at the end of each Ethernet cable run.

This will give me (hopefully) fairly good Wi-Fi coverage throughout the house as the the bedroom is at one end, the lounge at the other end and the kitchen is in the middle.

Upstairs there are spare bedrooms with it would be good to get Wi-Fi to at some stage but it is not the priority.

So my question is this: - What Deco units should I get? This will be 4 Deco units (one each for the hallway, bedroom, lounge and kitchen).

I am on a bit of a budget so do not really think I can afford Wi-Fi 7 devices so I have been looking at the X50/X55 units.

What would people recommend? I am a bit confused about compatibility as TP-Link seem to be in a quandry as to which mesh standard(s) to adhere to!

Do I need a different (better) device in the hallway and then 3 identical units for the satellites?

Presumably I will need a small Ethernet switch after the main router in the hallway?

 

Future considerations: -

Outside - I will add a TV with an IPTV box so will need an outdoor Deco

Outside - I will add Wi-Fi security cameras (opposite side of the house to the TV) so will probably need another outdoor Deco

 

What other things do I need to consider? For example, at a later date could I add a Wi-Fi extender or PowerLine if I find a room that doesn't get a decent signal?

 

Regards

  0      
0
#1
Options
7 Reply
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
a week ago

  @ICA-IT 

Hi,
We usually recommend using the same Deco nodes in a Deco network, and based on the current information you provided, the Deco X50/X55 can meet your requirements. However, since the Deco X50/X55 has only three Ethernet ports and the main Deco needs to connect to the front modem/router via an Ethernet cable, a switch is required if you want to connect the three satellite Deco nodes to the main Deco via Ethernet.

 

Our Deco models are compatible with each other, so if you add outdoor Deco models, they can join the existing Deco network. However, if the new Deco node connects to the existing Deco node via Wi-Fi, please ensure it's placed within the Wi-Fi range of the existing Deco node.

 

The Wi-Fi extender and Powerline can usually work with the Deco, but they can't build a mesh network. For example, there is usually no problem connecting the range extender to the Deco's Wi-Fi and then extending the Wi-Fi range. 

 

You can visit this website and then filter the Deco models to find the one you are interested in.

Best Regards

  0  
0
#2
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
a week ago

  @Solla-topee 

Many thanks for the reply.

I think I will get 4 of the Deco X50 units - or Deco X55? What is the difference?

Then add a switch such as the  TL-SG108 to distribute the Ethernet backhaul from the hallway to the 3 satellites.

When I mentioned PowerLine I was thinking of using PL adapters to create an Ethernet backhaul - is this possible?

Regards

  0  
0
#3
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
a week ago

  @Solla-topee 

Just a thought...

I have a couple of Deco E4 units.

I know that they are only 10/100Mbps ports but can I use them upstairs as satellites?

Will they be compatible with the X50 units?

Thanks

  0  
0
#4
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
Sunday

  @ICA-IT 

Hi,
1. You can go to this page, find the Deco X50 and X55, and check the COMPARE option at the top-right corner, then tap Compare to see the difference between them.
 

2. Usually, you can use our powerline adapters to build Ethernet backhaul between the Deco nodes. If you care about the actual download speed through the powerline adapters, it's recommended to pay attention to the powerline adapter's specifications. The article below may help you.
Explanation about the Powerline Rate and Actual speed of the Powerline Adapters
 

3. Our Deco models are compatible with each other. The Deco E4 can work with the Deco X50/X55.

 

Best Regards
 

  0  
0
#5
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
Sunday

  @Solla-topee 

Many thanks for the advice yes

Deco X50 units and 8-port switch ordered...

  0  
0
#6
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
Yesterday

OK, so all the devices are here - Deco X50 units and C660 cameras.

Does anyone have any words of wisdom (advice) regarding the installation?

For example, I have read that there can be issues after firmware updates causing backhaul to become unstable.

Is it best to update each Deco individually (if that's possible) to the same level before creating the network?

Any help would be much appreciated.

Thanks

  0  
0
#7
Options
Re:Basic Wi-Fi 6 Whole Home Mesh with Ethernet Backhaul - ISP is StarLink (Gen.3 )
8 hours ago

  @ICA-IT 

Hi, 
There are no known bugs in the latest Deco X50 firmware that would cause instability issues. You can refer to the video below to set up your Deco. If the Deco firmware is not up to date, you can upgrade it to the latest version via the Deco app after completing the setup.
How to Set Up a Whole Home Mesh Wi-Fi System
How to Update TP-Link Deco Firmware

Once you have set up and positioned the Deco units and confirmed that the Deco network is functioning correctly, you can proceed to set up the Tapo C660; then install the camera after the setup is complete.
How to Set Up Your Tapo Solar-Powered Pan/Tilt Security Camera Kit

Best Regards

  0  
0
#8
Options