Home Network Community > Deco > Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
< Deco

Early Access Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!

Early Access Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!

Early AccessFirmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
a week ago - last edited a week ago
Tags: #Official #Highlighted Thread #DoH/DoT
Model: Deco BE63   Deco BE65   Deco BE11000  
Hardware Version: V2
Firmware Version:

Hey Everyone!


We are excited to announce a pre-release firmware update for Deco BE65 V2.0, Deco BE63 V2.6, and BE11000 V2.6. This pre-release firmware introduces several new and advanced features, including DoH & DoT, Speed Limit, Internet Backup, and more! We encourage community members with these models to install this firmware and share your feedback.


Applies to:

Deco BE65(EU/US/AU/CA/UK)_V2.0
Deco BE63(US)_V2.6
Deco BE11000(US)_V2.6

 

 

Firmware Modifications

New Features/Enhancements:
 

Bug Fixes:
 

  • Fixed the behavior where the Online List doesn't show IP addresses of connected clients when Deco is in AP mode.
     
  • Resolved the behavior where QoS Total Bandwidth doesn't take effect as expected under certain circumstances.
     
  • Addressed the phenomenon where the Deco may restart automatically under certain circumstances. 


Download Link:

Deco BE65/BE63/BE11000_V2.0/V2.6

1.3.0_build_26012212_Beta


Note: 
 

  • Please ensure your Deco app is fully up-to-date.
     
  • This firmware cannot be downgraded directly to the previous 1.2.10/1.2.0 version.
     
  • There will be an official firmware release in the future. If you are not comfortable using pre-release firmware, please wait for the official release or contact our support teams for assistance.
     
  • Pre-release and Beta firmware should be used at your own discretion. We cannot guarantee the functionality of features or technical support for Pre-Release or Beta Firmware.
     
  • For detailed instructions, visit: How to manually update the firmware via web UI.

 

Additional Information

 

As always, we value your feedback. If you happen to encounter any concerns during or after the router firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.

 

  • Provide a detailed network layout, including how the devices are connected.
     
  • Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.

 

Thank you for your continued support and for being part of our community.

What's New? What is a VPN? What Can a VPN Do For Your Network? Optimize Your Network with the Wi-Fi Toolkit App Join our Official Subreddits: r/tplink, r/tapo, and r/omada_networks
  3      
 
  3      
 
#1
Options
3 Reply
Re:Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
21 hours ago

  @Ryan Some nice new features in this one. 

I installed it in the hopes of finding a resolution to a NAT loopback issue that appears to have popped up with the 1.2.0 update. Unfortunately, I'm still seeing the issue with this 1.3.0 update. After update, most of the web UI has disappeared, with only the system page remaining. Is that normal?

 

For the NAT loopback issue (I can access a server on my network directly via LAN IP, but not via external IP or hostname. This is intermittent but doesn't work more often than it does work), since I'm on the 1.3.0 prerelease, would that be a topic for this thread?

 

Thanks!

  1  
  1  
#2
Options
Re:Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
18 hours ago

  @justinross 

Yes, please feel free to leave your feedback here.

Do you save any screenshots that:

"After the update, most of the web UI has disappeared, with only the system page remaining. Is that normal?"

 

As for the NAT Lookback issue, is the internet connection type "Dynamic IP"?

It is recommended to check whether the current IPV4 address is the same as the IP address displayed here:https://whatismyipaddress.com/

By the way, what is this local server that you plan to access via external IP/DDNS domains?

How often do you usually run into this issue?

 

Wait for your reply.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Wi-Fi Heatmap ready for Test! ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re:Firmware 1.3.0 for Deco BE63/BE65/BE11000 V2/2.6 Adds DoH/DoT, Speed Limit, Internet Backup & More!
14 hours ago

David-TP wrote

  @justinross 

Yes, please feel free to leave your feedback here.

Do you save any screenshots that:

"After the update, most of the web UI has disappeared, with only the system page remaining. Is that normal?"

 

As for the NAT Lookback issue, is the internet connection type "Dynamic IP"?

It is recommended to check whether the current IPV4 address is the same as the IP address displayed here:https://whatismyipaddress.com/

By the way, what is this local server that you plan to access via external IP/DDNS domains?

How often do you usually run into this issue?

 

Wait for your reply.

Best regards.

  @David-TP 

After awhile (and a couple of Deco reboots), the web ui seems to be back to normal. Immediately after the firmware install, it was only showing the Advanced tab. 

 

Re: NAT Loopback:

1. Internet Connection Type is Dynamic IP.

2. Current IP matches that shown on whatismyipaddress.com

3. I've got a number of servers running in Docker containers in this host machine. Most of them are behind a reverse proxy (I was using Nginx, but am also trying out Caddy. The problem is happening with both, and with servers not behind the reverse proxy, as well as a couple I've tried not in Docker containers, just in case). 

I haven't managed to nail down a consistent pattern or timing on it, unfortunately. It seems to work for a while after a Deco reboot, but not always. I was wondering if UPNP being on was letting something else try to register the ports in question, but turning it off doesn't seem to have changed anything. 

 

For now, I've got a workaround in running my own DNS server for local network, so I can have the domains in question go to the local address instead of my public address, so I'm not too worried about a fix, but I'm happy to help troubleshoot, as I saw a user on Reddit with the same issue on 1.2.0, and figure I might be able to help figure it out.

  0  
  0  
#4
Options

Information

Helpful: 3

Views: 239

Replies: 3

Tags

Official Highlighted Thread DoH/DoT
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.