Red Blinking Light. (logs attached)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Red Blinking Light. (logs attached)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Red Blinking Light. (logs attached)
Red Blinking Light. (logs attached)
2022-10-10 11:01:17
Model: Deco M5  
Hardware Version: V3
Firmware Version: 1.5.6

Hi There,

 

I've succesfully set up the 3 x Mesh Deco. The signal is great. I have just had some loss of conenctivitiy with red blinking lights. This has now stopped. I restarted one of the Meshes not plugged into the router.

I have a Virgin Media Hub 3. The only thing I did was turn it on modem mode. Nothing else. Logs attached below:

"

Mon Oct 10 00:12:20 2022 user.notice IMPROXY: INFO[imp_verify_multicast_addr@245]: Group address 224.0.0.251 is Local Network Control Block

Mon Oct 10 00:12:33 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:33 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:disassociate

Mon Oct 10 00:12:33 2022 daemon.err client_mgmt: client(1A-27-F5-D3-5D-5F) disassocaite by if(ath12).

Mon Oct 10 00:12:34 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:34 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:associate

Mon Oct 10 00:12:34 2022 daemon.err client_mgmt: client(1A-27-F5-D3-5D-5F) assocaite by if(ath12).

Mon Oct 10 00:12:43 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:43 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:disassociate

Mon Oct 10 00:12:43 2022 daemon.err client_mgmt: client(1A-27-F5-D3-5D-5F) disassocaite by if(ath12).

Mon Oct 10 00:12:44 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:44 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:associate

Mon Oct 10 00:12:44 2022 daemon.err client_mgmt: client(1A-27-F5-D3-5D-5F) assocaite by if(ath12).

Mon Oct 10 00:12:55 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:55 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:disassociate

Mon Oct 10 00:12:55 2022 daemon.err client_mgmt: client(1A-27-F5-D3-5D-5F) disassocaite by if(ath12).

Mon Oct 10 00:12:55 2022 daemon.err client_mgmt: wireless client associate or disassociate.

Mon Oct 10 00:12:55 2022 daemon.err client_mgmt: client_mac:1A-27-F5-D3-5D-5F, client_ifname:ath12, client_action:associate"

It now looks to be working again, but I'm a little concerned this may occur again. Would anyone have a clue as to what caused it? Could be Virgin Media itself perhaps - There are no known issues in the area, however. 

Many thanks,
Chris

  0      
  0      
#1
Options
2 Reply
Re:Red Blinking Light. (logs attached)
2022-10-10 18:30:41

  @Chris-R,

Let me know if the issue persists, as you are just setting up the mesh system, this behavior may have been a result of the devices optimizing their connection between each other. When you were experiencing the blinking red lights, were you able to tell if the internet dropped out on the main router? Did the wired satellite units lose connection? 

Was the Red Blinking Light only on the one satellite unit? This would indicate that the satellite unit simply disconnected from the mesh and was searching fo a method to reconnect to the network.

  1  
  1  
#2
Options
Re:Red Blinking Light. (logs attached)
2022-10-10 21:07:59 - last edited 2022-10-10 21:13:05

  @Riley_S Thanks for the reply.
 

I noticed the two decos downstairs were blinking red. I didn't check the router connected one a lot. Never saw it blinking, though I might have missed it.
 

Heres the logs from my virgin router. The issue occurred around 11:00am - 1pm I think;

 

10/10/2022 21:00:26 notice LAN login Success;CM-MAC=18:35:d1:ba:6d:1b;CMTS-MAC=04:62:73:e4:fe:ad;CM-QOS=1.1;CM-VER=3.0;
10/10/2022 11:46:16 critical No Ranging Response received - T3 time-out;CM-MAC=18:35:d1:ba:6d:1b;CMTS-MAC=04:62:73:e4:fe:ad;CM-QOS=1.1;CM-VER=3.0;
10/10/2022 10:46:52 notice LAN login Success;CM-MAC=18:35:d1:ba:6d:1b;CMTS-MAC=04:62:73:e4:fe:ad;CM-QOS=1.1;CM-VER=3.0;
10/10/2022 08:42:13 notice DHCP Renew - lease parameters tftp file-cmreg-vmdg505-bbt060-b.cm modified;CM-MAC=18:35:d1:ba:6d:1b;CMTS-MAC=04:62:73:e4:fe:ad;CM-QOS=1.1;CM-VER=3.0;


 

It's been fine the rest of the day & evening. I wonder if reconnecting the 1 satellite deco helped fix it? Thanks 

 

Chris  

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 565

Replies: 2

Related Articles