Connecting VR600 as a router to existing modem / router.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Connecting VR600 as a router to existing modem / router.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Connecting VR600 as a router to existing modem / router.
Connecting VR600 as a router to existing modem / router.
2019-12-04 16:08:15 - last edited 2020-02-12 08:47:39
Model: Archer VR600  
Hardware Version: V2
Firmware Version:

Hello

I'm trying to connect VR600 to an existing modem router (it's from our cable company in Israel).

I was able to connect an older TP-LINK model (TL-WR1043ND) with wifi and wire connection.

When I try to connect the VR600, I get no internet at all.

If I don't allocate a static IP, it will get the same IP as the modem router, and will give a conflict between both.

If I enter different IP address it will give no internet at all.

I was trying to set it as wireless router, tried to disable DHCP, trie a lot of things that I read about, with no succses.

Can someone give me some hints or instructions?

The physical connection is between the wan/lan port in the VR600 to port #1 in my modem / router.

I need the VR600 for connecting my usb printer to the net (if it matters) and its far away from the modem router.

Thnaks a lot.

  0      
  0      
#1
Options
1 Accepted Solution
Re:Connecting VR600 as a router to existing modem / router.-Solution
2019-12-05 08:05:29 - last edited 2020-02-12 08:47:39

@NitziGertzi 

 

You can set it up as the regular wireless router mode or the access point mode to boost network. Considering you want to use the USB printer, you can set it up as the regular router first. 

 

Below is the instruction to configure it: 

https://www.tp-link.com/support/faq/1731/

 

Before you change the operation mode, please go to network-LAN settings page to change the IP address; make it different from the main router; for example, if the main router is 192.168.1.1, then change the IP of VR600 to 192.168.0.1. 

 

May it help. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:Connecting VR600 as a router to existing modem / router.-Solution
2019-12-05 08:05:29 - last edited 2020-02-12 08:47:39

@NitziGertzi 

 

You can set it up as the regular wireless router mode or the access point mode to boost network. Considering you want to use the USB printer, you can set it up as the regular router first. 

 

Below is the instruction to configure it: 

https://www.tp-link.com/support/faq/1731/

 

Before you change the operation mode, please go to network-LAN settings page to change the IP address; make it different from the main router; for example, if the main router is 192.168.1.1, then change the IP of VR600 to 192.168.0.1. 

 

May it help. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
Re:Connecting VR600 as a router to existing modem / router.
2020-11-08 11:57:24

@Kevin_Z 

cant it be configured to be a wired extender?

like other tp-link routers

i tried your way, configure the other device(modem) to be on 192.168.1.1 and the VR600 to be on 192.168.1.15 while the modem DHCP range is 192.168.1.20-254

i turned off the DHCP on th VR600 but yet he cant configure the connection between the modem and the VR600. still there is no internet and the both networks works as two separated networks, and they cant see each other

  0  
  0  
#8
Options
Re:Connecting VR600 as a router to existing modem / router.
2020-11-13 09:57:09 - last edited 2020-11-13 09:57:36

@avici 

Good day.

Thanks a lot for your time and patience.

Have you seen this link to check your configuration: https://www.tp-link.com/support/faq/2655/

Could you please help me check the IP address and default gateway when the device connected to the VR600?

Thank you very much.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#9
Options