Not working TAPO c200 after updating

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Not working TAPO c200 after updating

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Not working TAPO c200 after updating
Not working TAPO c200 after updating
2020-09-20 14:09:23 - last edited 2023-12-04 01:08:58
Model: Tapo C200  
Hardware Version:
Firmware Version:

I wanted to put new software on the camera, but it was not updated, and the camera froze. The red indicator and night light are on. Reset does not help. Off-on too. I was using the camera for literally 30 minutes. The program itself does not see it either. What to do in this case?

  4      
  4      
#1
Options
1 Accepted Solution
Re:Not working TAPO c200 after updating-Solution
2022-01-14 03:49:59 - last edited 2023-12-04 01:12:05

 @mrnice03 

Hello everyone, 

If the Tapo C200 camera got a firmware update failure, make sure you have tried to factory reset the camera with the camera powered on, check camera still responds to a factory reset, or if the camera still broadcasts the Tapo Camera _XXX default SSID,  or if the  LED flashes amber and green.

How to reset my Tapo camera

 

If a factory reset does not help, you can refer to the instructions below to troubleshoot.
What to do if my Tapo Camera gets bricked or doesn't respond to a factory reset?

 

Best Regards

Recommended Solution
  1  
  1  
#12
Options
11 Reply
Re:Not working TAPO c200 after updating
2020-09-22 01:41:56

@Ievgen 

Good day. 

Thank you very much for your time and patience.

Did the system LED still lit up?

When you reset the camera, would the system LED start blinking?

And may I know where are you located?

Was there any abnormal behavior during the firmware update?

Thank you very much.

  0  
  0  
#2
Options
Re:Not working TAPO c200 after updating
2020-10-23 10:59:37

@Ievgen i am facing the same issue

  5  
  5  
#3
Options
Re:Not working TAPO c200 after updating
2020-10-23 11:03:57

@Ievgen 

camera not responding after firmware update, camera only showing 4 Red LEDs, powered on, 

and nothing else

i have tried reset methods but unsuccessful

please advise how to reset without mobile app, because i cannot find my camera in mobile app now

 

  10  
  10  
#4
Options
Re:Not working TAPO c200 after updating
2020-10-27 05:48:05

@faisalmasood 

Good day,

Thanks a lot for your time and patience.

Please refer to this link to reset the Tapo cameras:

https://www.tp-link.com/support/faq/2705/

 

By the way, where are you located and how long have you had the camera?

Thank you very much.

  0  
  0  
#5
Options
Re:Not working TAPO c200 after updating
2020-10-30 16:42:15

@Brook 

today iv just got new one was workin and after I made update to firmware it’s not responding no more , ps nothing up normal happened or any wrong with connections while the update. . I did reset more than 5 times with all ways , plz help

  4  
  4  
#6
Options
Re:Not working TAPO c200 after updating
2020-11-03 08:52:16

@Johnson-zayed 

Sorry for the delay.

Nice to see you again.

Please refer to the reply on another post.

And if the reseller refused the warranty service, once the receipt is confirmed later, TP-Link could still help you get the replacement.

Thank you very much.

  0  
  0  
#7
Options
Re:Not working TAPO c200 after updating
2021-03-03 10:48:14

@Solla-topee i had the same issue with tapo c310. Whats wrong with tp link. Issues always arise with firmware updates

  0  
  0  
#8
Options
Re:Not working TAPO c200 after updating
2021-11-20 10:18:23

@Jjjesie 

 

hello

 

i have the same issue with my c200 after the sw update yesterday the camera is frozen , only the infrared leds are on , I can not reset the camera I can not make anything . Somebody solved this problem ?? What I can do ? 

  3  
  3  
#9
Options
Re:Not working TAPO c200 after updating
2021-12-25 16:12:53

@Ievgen 

hello,


I update the camera software today and the now the red light is on all the time and frozen. Reset , power on and off does not help. Total 4 cameras affected.

please help..

  0  
  0  
#10
Options
Re:Not working TAPO c200 after updating
2022-01-13 11:43:51

@Ievgen 

 

I have the same issue here.. I'm from cavite. please help us with this issue.. thank you so much.

  1  
  1  
#11
Options