Solution iPhone iOS14 recognizing the range extender wireless network as "weak security"
![](/avatar/avatar-20.png)
Problem phenomenon:
If you have since updated your iPhone you may see the range extender’s Wi-Fi shown as having weak security. This is due to the range extender supporting the mixed WPA/WPA2 (AES/TKIP) by default for compatibility purposes. The iPhone now recognizes WPA as a weak security type. This may also be the same with other security suites with a similar notification.
Why range extender network is displayed as “Weak Security”?
A range extender is essentially a device that connects to an existing Wi-Fi hotspot and repeats the signal, so generally, it will generate the wireless security of the host Wi-Fi hotspot. While the default wireless security of the TP-Link range extender itself was auto, it supports WPA2+AES, as well as older WPA+TKIP for compatibility with older devices. Even though your iOS device recognizes the range extender network as weak security, it connects to the network with the stronger WPA2+AES by default, so there won’t be any security concerns upon to this point.
Troubleshooting : What to do if IOS devices shows ' weak security'?
Steps 1
Make sure main router is on WPA2-PSK (AES) and IOS devices does not show' weak security' when connected to main router
Here is a related guide to check security type on router:
Why my iOS14 warning weak security when I connect to TP-Link Wi-Fi
Step 2
Confirm Range extender is on the latest firmware :
Download the latest firmware for range extender from tp-link Download Center or make sure firmware is up-to-date on TP-Link Tether APP.
(select hardware version first before download the corresponding latest firmware)
Step 3
Restore the range extender to the factory default settings and re-associate the host Wi-Fi through the web page Quick Setup Guidance is as below:
https://www.tp-link.com/support/faq/2485/
RESET: with RE powered on, use a pin to push the reset hole until all the LEDs flash once
Note: if you use Tether app to install Range extender, update Tether app in Google Play or APP store first before set up.
If the above does not fix the problem, please report back with some information to help locate the issue:
1. Model of router & a photo of the wireless security settings on router
2. firmware and hardware version of range extender, better to attach a photo showing weak security
3. do you use Web or Tether to set up the extender
Note:
If some of your devices cannot connect to the whole Wi-Fi network after these modifications, you may need to change the wireless security back.
Let the community know if you have any further inquiries, thanks a lot~
More Articles:
TP-Link Range Extender Setup (Range Extender Mode)
Has connected to TP-Link extender but no internet, what can I do?
Unable to Connect to WiFi Extender or Saying Incorrect Password
What should I do if Internet speed becomes slow via Range Extender?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@Solla-topee Any firmware update for RE200 V2?
- Copy Link
- Report Inappropriate Content
I did not do much testing, but it seems to me that when the device is in extender mode and advertises the same SSIDs as the original AP, clients are not offered the possibility to authenticate using a PIN. I might be wrong... I have verified though that when the extender advertises new SSIDs, the PIN is an authentication option.
- Copy Link
- Report Inappropriate Content
@Solla-topee what about a (beta) firmware update for RE305 v1 (EU)? do you have an ETA for a release date? thanks
- Copy Link
- Report Inappropriate Content
saisrujan wrote
TP-Link wrote
Hi, all!
Good news. The beta firmware to fix the weak security issue for RE450 v3 has been released:
https://static.tp-link.com/2020/202012/20201210/RE450_V3_201209.zip
Please feel to update here if there is any issue after the firmware update.
Thank you very much.
@TP-Link Thanks for sharing the beta firmware.
The firmware fixed the issue and now the extender is not using TKIP anymore, and the whole network is using AES. But the issue is that after a few hours, any devices connected to the extended network loses internet connectivity. I see something like the following:
I still can access the local network but I can't access the internet. Devices connected to the base network continue to work fine and the issue is only with the extender. The only way to fix this is to restart the extender. It's hard to figure out when this happens, sometimes happens in an hour after restart, sometimes it takes 8 hours so it is unreliable. Unless this is fixed, I can't really use the extender because I am getting dropped off from calls and video conferences, and for reliability I have to connect to the base network and that slows me down and defeats the purpose of buying this extender.
@TP-Link Did your team investigate this? Why does the extender blocks internet connection while it allows local network? There is no clue anywhere that something is wrong, except that the internet doesn't work when the device is connected to the extender. Why is this happening?
- Copy Link
- Report Inappropriate Content
I just went through some tests with the repeater and the new firmware (and the problems with it). WPS is always active, whether it is the SSID of the main network or a custom one. I only got the WPS turned off by switching to AP mode beforehand and disabling the WPS there. This configuration is apparently retained when you then switch back to repeater mode.
With kind regards
nobbi
- Copy Link
- Report Inappropriate Content
I have 3 x TPLINK RE450 v1, one belongs to my neighbour although I manage it for them, these are also showing "weak security" when using iPad or iPhone. I was very surprised to see mention of various other devices with this issue but non for the RE450 v1 a device many others in the UK have access to and which is still available here to buy new.
Again a software update is also required for this popular device as a matter of urgency.
Thank you.
- Copy Link
- Report Inappropriate Content
I need firmware update for RE500 range extender as it has weak security issues just like other tp-link extender.
Can you post a link where I can download ?
- Copy Link
- Report Inappropriate Content
@Solla-topee is there any update for RE455v1?
- Copy Link
- Report Inappropriate Content
@yaroslavpp Hi there.
Go online to TP-Link.com and find the User Guide for the RE455 v.1
Go to Chapter 5 Manage your extender.
Section 4 Upgrade the Firmware. Then follow the instructions to upgrade.
The upgrade is best done with the extender linked directly to your computer via an Ethernet cable and the system then uses the extender's own internet connection. After I downloaded the software and rebooted, I actually had to reset the extender using the reset hole on the extender itself.
Having done all this my iOS phone and iPad no longer give the weak security message.
I must add that my extender is the RE350 v3 and I have no idea if the firmware upgrade on the 455 v1 will be successful.
- Copy Link
- Report Inappropriate Content
@The_Highlander Hello i have a TL-WA855RE 5.0 wifi extender and im getting the weak security problem when trying to connect to my iphone and ive tried resetting it and restarting it but nothing is working my hardware version is 1.0.0 Build 191219 Rel.51831n (8583) this problem started yesterday and when i go to the web version and login it says no internet but its connected to the router and everything else is fine. Is there an update i can do to fix these problems?
- Copy Link
- Report Inappropriate Content
![](/avatar/avatar-20.png)
Information
Helpful: 3
Views: 66294
Replies: 116
Voters 2
![voter's avatar](/avatar/default.png)
![voter's avatar](/avatar/avatar-5.png)