@Kevin_Z 

Hi, I updated to try to solve the multiple problems of the A6 V4 in Access Point mode:
- the LAN ports are disabled
- it is not possible to deactivate the DHCP server 
- the web interface is no longer accessible
- it is not possible to access the configuration even from the app
- wifi keeps dropping, unusable

exactly the same problems I had before the update

Considering that these are devices straight out of the box, and the same problem occurs on all three, I think it's a bigger problem, is there a solution or should I proceed with a return?

  @Kevin_Z hi! Will it be available for lower rev. version? I have c80 with 1.0 model board, but i really like VPN implementations 

Also there was talk about "Ethernet check ping" what the point of this function if it's not work correctly? 

My firmware version is 1.13.2 Build 230824 Rel.74702n(5255) 

Due to electricity problems in my home i have regular (probably 1 or 2 times per month) Ethernet restarts 

And EVERY time Archer can't connect to ethernet in auto-mode, every time it waits while i come back home from work and send it to reboot manually, and only after that i got back to live 

So... yes. Why do we need ping service if it doesn't work correctly? 

@Kevin_Z 

Hi.

I have the Archer C80 2.20 with the latest Firmware Version:
1.14.0 Build 240617.
Since it was updated to this latest firmware, in the Client List Management section, the Real-time Rate is updated every 30 seconds.
With the previous firmware (1.13.2 Build 230824) it was updated every 2 seconds which made it easier to see the bandwidth consumption of my devices.
Could you please fix this delay in updating the Real-time Rate of the bandwidth consumption of the devices connected to my Archer C80?
This is detrimental to me because when the measurement is updated every 30 seconds you cannot clearly see which device is consuming bandwidth correctly.
If it is updated as before every 2 seconds you could see the consumption of the devices in real time and it helped to see which devices were consuming a lot of bandwidth and detect problems and solve them.
This happens with a PC with Windows 10 and Chrome or Firefox.
Regards.

  @Kevin_Z 

HI,

thanks for replying

- all three have the same problem
- network layout: Internet Router (10.120.44.15 DHCP SERVER) -> Tplink
- I have done multiple factory resets with always the same result

I just did a factory reset again, I'll summarize the steps and attach the screenshots:

- I connected my PC via LAN on port 1 and the router on the WAN port (file just after factory reset)
- the tplink releases address 192.168.x.x, I connect to the web interface, I do the quick setup without changing anything (file: network map, firmware)
- after switching to access point mode the LAN port is disabled (file: after switch to AP) and it is not possible to connect to WiFi
- you cannot access the web interface via LAN or even from the app (File: app)
- by disconnecting the WAN cable the LAN port becomes active again (file: Unplug WAN)
- the tplink releases addresses of the class of the network in which it should be inserted: 

Ethernet 4 Ethernet Card:

   Connection-specific DNS suffix:
   Link-local IPv6 address. : fe80::15f8:f6c8:4fd8:9bff%2
   IPv4 address. . . . . . . . . . . . : 10.120.44.181
   Subnet mask . . . . . . . . . . . . . : 255.255.252.0
   Default gateway. . . . . . . . . : 10.120.44.158

releasing itself as a gateway

- in this way it is possible to connect to the web interface but it is not possible to deactivate DHCP (File: dhcp server)

In conclusion, the access point is unusable (the wifi does not connect and the LAN is disabled), it is not possible to access either the web interface or via the app

  @Kevin_Z Hi.

I have the Archer C80 2.20 with the latest Firmware Version:
1.14.0 Build 240617.
Since it was updated to this latest firmware, in the Client List Management section, the Real-time Rate is updated every 30 seconds.
With the previous firmware (1.13.2 Build 230824) it was updated every 2 seconds which made it easier to see the bandwidth consumption of my devices.
Could you please fix this delay in updating the Real-time Rate of the bandwidth consumption of the devices connected to my Archer C80?
This is detrimental to me because when the measurement is updated every 25-30 seconds you cannot clearly see which device is consuming bandwidth correctly.
If it is updated as before every 2 seconds you could see the consumption of the devices in real time and it helped to see which devices were consuming a lot of bandwidth and detect problems and solve them.
This happens with a PC with Windows 10 and Chrome or Firefox.
Regards.

  @Kevin_Z Hi.

Thank you very much for your reply.
The measurement is accurate for each client.
What changed is that the update is done every 25 or 30 seconds.
So, since the measurement is no longer in real time, it is not possible to distinguish the consumption or bandwidth for each device.
With the previous firmware 1.13.2 Build 230824, since the update was every 2 seconds, the bandwidth used in real time for each connected device could be correctly seen.
Can this problem be fixed in a new firmware version?
Regards.