Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control

Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control

69 Reply
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
2024-10-02 18:34:07 - last edited 2024-10-02 18:35:27

@azafrak  Are you sure 160 MHz Channel width selection was absent before? 

  0  
  0  
#22
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
2024-10-02 18:36:01
Yes. If you read the previous comments, you can see this.
  0  
  0  
#23
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
2024-10-03 18:53:09 - last edited 2024-10-03 18:53:34

  @azafrak Can you check ping time and packet loss with 80MHz channel width for 5Ghz channel. Becauze my whole problem with x60 has been in mid to low 5Ghz channel signal strenght, the ping time starts spiking. And much as tried to search documentation about 160 MHz vs 80Mhz - it's only recommended if u are in direct line of sight with AP or need that excess speed.

  1  
  1  
#24
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago - last edited 3 weeks ago

  @David-TP with regards to the added support for Matter in this update, Can you advise on whether the X60 will then have the ability to "commission" a Matter device once added, and then put the device into "pairing mode" so it can be added, in my case to a Hubitat C8 hub, Thanks

Regards,

Steven

  1  
  1  
#25
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago

  @David-TP 

 

Hello,

 

since the update to 1.3.0, I no longer receive push notifications via the Android Deco app when a new device connects to the network. I had the same problem with the X50 V1 after the update to 1.5.5. Can you check this please? Thanks.

 

best regards

Paul

  1  
  1  
#26
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago

  @REDMrMojo 

Hi, Do you plan to manage the added Matter devices under "Smart Home" on the Deco APP via Hubitat C8 hub?

- For example, Tapo P110M was added through Matter on the Deco APP and Hubitat C8 hub was also connected to Deco Wi-Fi. You wish Deco being able to entrust the P110M to Hubitat C8 hub.

 

There hasn't been tested yet.Most of the cases I have received is to manage the Matter supported devices through Deco APP directly. So I don't think it is available now.

Thank you very much and best regards.

 

  1  
  1  
#27
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago

  @delong91 

Hi, Would there be any notifications inside the Deco APP>Message?

 

Could you please install the beta APP here to see whether it helped:

Deco APP 3.8.36 --- Greatly Optimized Network Management Experience

 

If not, please refer to this link to help me submit the Deco APP log:

How to submit Deco APP log

 

Thank you very much and best regards.

  0  
  0  
#28
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago

  @David-TP 

 

Hi

 

thank you very much for the answer.

 

Yes, notifications about new devices are displayed inside the app.

 

I just installed the beta app and connected a new device but i dont recieve any push notification.

 

I sent you the app log.

 

best regards

  1  
  1  
#29
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago

  @David-TP By Mater support, what does that reffer to? Can the Deco act as a Matter Hub or is IPv6 enabled and Thread support?

  0  
  0  
#30
Options
Re:Deco X60_V3/3.2-1.3.0 Supports ECO Mode,WireGuard VPN and WiFi Access Control
3 weeks ago - last edited 3 weeks ago

  @David-TP 

 

Hello again,

 

1. Sometimes devices from the guest network that are offline are displayed in the offline list under the main network.

 

2. After a restart of my Deco, one device (TV GQ65S90CAT in the picture) no longer showed me which frequency band (2,4 or 5 GHz) it is connected to. After a second restart, the second device (SB HW-Q810GC in the picture) was also not displayed and them are still not displayed. The connection symbols are also missing in the overview of connected devices. So far, the error has only occurred with Samsung (TV and Soundbar) devices in my case. The devices still work perfectly in the network. Im still using android beta app.

 

 

after second restart:

 

Best regards

Paul

  1  
  1  
#31
Options