Early Access Deco BE65/BE63/BE11000_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup
This Article Applies to:
Deco BE65(EU/US/AU/CA/UK)_V2.0
Deco BE63(US)_V2.6
Deco BE11000(US)_V2.6
Hey Everyone!
We are excited to announce a pre-release firmware update introducing DoH & DoT, Speed Limit, and Internet Backup, as well as other advanced features for Deco BE65/63/BE11000. We encourage users to install this firmware and share their feedback with us.
Firmware Modifications
New Features/Enhancements:
- Added WiFi Heatmap. (It also requires the Deco App version to be: 3.10.133 for IOS and 3.10.80 for Android.)
- Supported fixing a specific port as the WAN port.
- Added Hybrid Mesh feature.
- Added Internet Backup feature.
- Added DoH & DoT feature.
- Added Speed Limit feature for client devices.
- Optimized HomeShield feature.
- Improved System Stability.
Bug Fixes:
- Fixed the NAT Loopback issue.
- Fixed the issue where the Online List doesn't show IP addresses of connected clients when Deco is in AP mode.
- Resolved the issue where the Qos Total Bandwidth doesn't take effect as expected under certain circumstances.
- Addressed the issue where the Deco may restart automatically under certain circumstances.
Download Link:
Deco BE65/BE63/BE11000_V2.0/V2.6 |
1.3.0_build_2602261_rel_21001_Beta 2026.3.9 updated |
Update Notice:
- Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
- Please make sure the Deco APP is up-to-date.
- This firmware can’t be degraded directly to the previous 1.2.10/1.2.0 version.
- How to manually update the firmware via web UI.
As always, we value your feedback. If you happen to encounter any concerns during or after the firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.
- Provide a detailed network layout, including how the devices are connected.
- Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.
Thank you for your continued support and for being part of our community.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
Firmware v1.3.1 was not developed in response to your issue; it may not help in your case. Please try setting the Deco BE65 that connects directly to the router as the main Deco, and then test whether this helps. If not, please feel free to reply to me.
How to Change the Main Deco Unit
Best Regards
- Copy Link
- Report Inappropriate Content
Hi,
If you are experiencing problems with the Deco BE65 Pro, it's recommended that you contact the technical support team for assistance.
Best Regards
- Copy Link
- Report Inappropriate Content
Hi,
Please provide more details about the disconnect phenomenon for analysis.
1. What's the model number of your Deco? How many Deco units do you have?
2. Please describe your network diagram, such as internet cable--main deco ))(( satellite deco, etc.
3. When the disconnect issue occurs, what's the LED status on the Deco nodes? Do all client devices lose internet connectivity even when connected to the Deco's Wi-Fi? Do they return to normal automatically?
4. How often does the disconnect issue occur?
Best Regards
- Copy Link
- Report Inappropriate Content
My model is BE65. I have two BE65 routers connected to my modem. Since updating to version 1.30, I've seen a red light on the Wi-Fi indicator in the morning, which then returns to normal after a while. When the light is red, there is no Wi-Fi, but when I checked my modem, it was working fine. The other Wi-Fi router downstairs is still connected. Isn't this a bug?
- Copy Link
- Report Inappropriate Content
Hi,
Based on your description, I guess your topology might be Internet cable —modem — downstairs main Deco))((RE Deco, and the satellite Deco is unstable. If so, you can follow the instructions below to troubleshoot.
Fix unstable connection when connected to the Deco network
If not, please describe your network diagram. Does Deco work in Router mode? You can also try swapping the two Deco nodes' locations, set another Deco as the main Deco, and check if the issue follows the specific Deco or location.
How to Change the Main Deco Unit
Best Regards
- Copy Link
- Report Inappropriate Content
I'm trying to figure out a solution, because this has never happened before; the problem only appeared after updating to this version. I'm testing from various sources, and I'm also using AP mode.
- Copy Link
- Report Inappropriate Content
Did as suggested, gave it a bit to see if the issue reoccurs and same thing happened, and issue followed the Deco unit; now the main was showing as connected via wifi and not the ethernet backhaul despite mikrotik showing a 2.5g connection being up.
I understand 1.3.1 was not designed to address this issue but at this stage, I'd give it a shot to see if coincidentally I get better results. Thanks!
- Copy Link
- Report Inappropriate Content
Please be careful with the link below:
Virus scanner reports: Malicious website (https ://ipywev.com) blocked
Hi,
Based on your description, I guess your topology might be Internet cable —modem — downstairs main Deco))((RE Deco, and the satellite Deco is unstable. If so, you can follow the instructions below to troubleshoot.
Fix unstable connection when connected to the Deco network
If not, please describe your network diagram. Does Deco work in Router mode? You can also try swapping the two Deco nodes' locations, set another Deco as the main Deco, and check if the issue follows the specific Deco or location.
How to Change the Main Deco Unit > This one is infected
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi,
The link to the instructions (How to Change the Main Deco Unit) is https://www.tp-link.com/support/faq/2400/, rather than the website reported by the virus scanner.
Best Regards
- Copy Link
- Report Inappropriate Content
Information
Helpful: 6
Views: 33936
Replies: 235
Voters 4
