Configuration Guide How to set up Ethernet Backhaul with your Deco devices
Ethernet Backhaul is a feature that makes it possible to wire the Deco units together to optimize the bandwidth and network stability.
Normally, after wired Deco units with an Ethernet cable, the Ethernet backhaul will take effect automatically.
Typical connection structures for Ethernet Backhaul
QA
Q1: Which switch models support Ethernet backhaul?
Most of the switches on the market support Deco's Ethernet backhaul feature. If you don’t have a switch or if your switch is verified not compatible with Deco Ethernet Backhaul, the following models will be a good choice:https://www.tp-link.com/home-networking/all-soho-switch/
Q2: To use the Ethernet Backhaul feature, do I need to wire all my Deco units?
Nope. The following network layout works as well.
Q3: How do I know if Ethernet Backhaul takes effect?
Q4: Why my satellite Deco's signal source shows "Wi-Fi" instead of "Ethernet" in the Deco app even if the main Deco and the satellite Deco are connected to the same switch?
Please refer to the suggestions on this link:Ethernet Backhaul not working
Q5: Why my Deco units become unstable once they're connected via a switch?
The Deco Ethernet backhaul feature is based on the standard IEEE 1905.1 protocol. However, we find that some switches, mainly the D-Link switches, will not forward packets based on IEEE 1905.1 protocol, causing all Deco units in a network loop and becoming quite unstable, you might consider changing another switch or contacting switch’s support directly. TP-Link Switches are mostly compatible with our Deco’s Ethernet backhaul.
Q6: Can I set up different Deco models such as M5 and M9 Plus together through Ethernet backhaul?
Yes, just configure and add different Deco models in the same Deco network. After that, you can wire them to set up the Ethernet backhaul connection.
You could refer to the link to learn how to add different Deco models in the same network.
Q7: Can I use one Ethernet port on the Deco for Ethernet backhaul and the other to connect a computer?
Yes. For more details, please refer to How to use Ethernet Ports on Deco?
Q8: Can I use a pair of powerline adapters to build Ethernet Backhaul, like Main Deco---master Powerline adapter~~~extended Powerline adapter---satellite Deco?
Yes and please keep in mind that the Ethernet Backhaul speed now will depend on both the Ethernet cable quality and Powerline rate.
Related Article: General questions about Ethernet Backhaul feature on your Deco
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I've attempted to wired backhaul the units together with no luck, they would create different networks and the worst part is I have to "TURN OFF/ON" wifi again on a MESH network.
Here's the setup
ISP Router in AP mode and we have no password for it
-
Ethernet to upstair 3com switch
-
3com switch distribute ethernet to every room in the house (every room has an ethernet socket)
-
Deco is connected via ethernet in Master Bedroom
-
Each Deco after is set up wirelessly and place throughout the house (results in slow speed from some deco, no idea yet as to why)
-
Connect one-by-one into the ethernet port from wall (start creating their own network)
-
Ultimately I'm stuck with wireless backhaul with less than 1% the speed of my package at time (more often than imagine)
QOS is set to standard
Any clue as to how we can solve this?
- Copy Link
- Report Inappropriate Content
Case 2) If your ISP router is in bridge mode I would recommend installing a router mode M5 unit between the ISP router and the 3com switch. So lan cable from ISP router to M5 unit. And lan cable from same M5 unit to switch. All other M5 units then connect with wire to same switch.
My own setup is as per Case 1 and a wireless speed test run on my phone gives almost exactly the same speed as when run on a computer connected by lan cable to the same network.
- Copy Link
- Report Inappropriate Content
Good luck!
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have the suspicion that it's because I'm using the Deco on AP mode, something I suspect very few people does use, as it wasn't even a feature until a firmware update added it.
The situation is the following: I have three decos in a straight line, with one of the ends working as the main one. If I only have the main one connected with an Ethernet cable (to my ISP's router), everything works well, except for the speed that it's not ideal (I have symmetric 600Mpbs Internet connection and a Gigabit NAS, and using the Decos as repeaters and APs slows the speed a lot).
The problem arises when I plug an Ethernet cable to the middle Deco; I connect the cable with the Deco turned on and it's light solid green, then the light turns solid red for a second, and then back to solid green, something that it's supposed to tell you that everything is working; except that the wifi does not: the wifi clients show that they're still connected and with good signal strenght, but there's no Internet and the Deco app gets stuck trying to connect to the Decos.
If I try to Ping the middle Deco from a Ethernet connected computer while it has the Ethernet cable plugged in, fails about 1 of every 4 pings. If I unplug the Ethernet cable from the Deco, everything works well again (after a minute or so), and when I ping the middle Deco, all pings work ok.
I'm using the lastest firmware version (1.2.3 Build 20180819 Rel. 68100) on all three Decos.
- Copy Link
- Report Inappropriate Content
I have exactly the same problem as you - have you found any solution?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 19
Views: 464155
Replies: 403