Tapo C100 firmware 1.3.6 V 2 Notification Not Working more

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tapo C100 firmware 1.3.6 V 2 Notification Not Working more

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-16 17:45:12
Model: Tapo C100  
Hardware Version: V2
Firmware Version: 1.3.6 Build 230513 Rel 47982n(4555)

 

I have 8 Tapo C100 cameras, after the upgrade to the new firmware 1.3.6 from the 1.1.15, the movements notification doesn't work on the app.

The upgrade Is installed on 6 cameras only, on the others 2 cameras Is still installed the 1.1.15 firmware and the notifications working yet.

  2      
  2      
#1
Options
5 Reply
Re:Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-17 09:43:35

  @DCosimo 

Hello,  

Thank you for the case report, and please help confirm the following information.

 

1. For a Tapo C100 with the new firmware, please go to the Tapo app>click on it>go to Camera Settings>Detection & Alerts>Motion Detection, is this feature enabled? If so, please describe your settings on this page.

On the Detection & Alerts page, please go to Activity Notifications, have you enabled it and the schedule set to Always?

If the AI Detection feature is turned on, please let me know what AI detection features have been enabled.

 

2. If the notification and detection settings are correct for the C100, but you can't receive the notification when an event is detected, please go to the Tapo app>Home>Message icon at the top right corner, and can you see the notification for this event?

 

3. Please let me know the MAC address of the C100 you used to test, and the time, date, and time zone when the camera detects an event.

 

Best Regards

  0  
  0  
#2
Options
Re:Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-17 12:10:04

  @Solla-topee 

Settings:

Motion Detection: enabled

Activity notification: enabled and set It to Always

IA detection: human enabled (i tried all disabled too, the effect Is the same)

On the Tapo App i've not any alert in the top right, but i can read in the the "Cameras" schedule in the bottom, in the Windows of the C100, "last Activity 0 hours ago"

 

So i think the problem Is the POP UP on the app

 

MAC: B4-B0-24-55-D4-90

Last event detected 2023-07-17 --- 14:05:41

  1  
  1  
#3
Options
Re:Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-18 07:11:49

  @DCosimo 

Hi,
If the Tapo cameras connect to an NVR/NAS, please disconnect them from the NVR/NAS and then check if the notification feature will work.

Best Regards

  0  
  0  
#4
Options
Re:Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-18 07:52:05

  @Solla-topee 

After the camera was disconnected from the Nas and restarted, the notifications works again.

But i need it works during the camera Is connected to the nas as the last firmware versione, Is It possibile?

  1  
  1  
#5
Options
Re:Tapo C100 firmware 1.3.6 V 2 Notification Not Working more
2023-07-18 08:53:34

  @DCosimo 

Hi,

I have reported the issue to the tech team, and they will likely reach out to you via email to continue troubleshooting your issue. Please check your email box and confirm.

Best Regards

  0  
  0  
#6
Options