D230S1 Setup failure
I've just purchased the above. The Hub has set up OK. The doorbell flashes red/greed yet despite many resets and battery replacements, won't connect to the Hub.
Before I return this as a faulty unit, is there anthing else I should try?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi,
Please try the following steps to troubleshoot.
1. Please ensure the hub Tapo H200 is configured successfully and working. Let me know the LED status on the hub.
Please try the instructions below if the hub can't be configured successfully.
Troubleshooting: What to do If Fail to Configure Tapo H200 Hub
2. If the hub is working, try to factory reset the doorbell camera. Generally, the camera will have a flashing red and green light after reset.
3. Try to set up the doorbell camera, and let me know which step you are getting stuck on if fail to set it up and what error message appears.
How to Set Up Your Tapo Video Doorbell Camera Kit (Tapo D230S1)?
You can check if the following instructions will help.
What can I do if the battery-powered cameras fail to pair with the Tapo H200?
Best Regard
- Copy Link
- Report Inappropriate Content
Hi,
What status of the LED on the doorbell camera? Such as flashing red quickly, solid red, etc.
When you press and hold on the SYNC/RESET Button on the doorbell camera for 5s, any changes to the LED status?
Anything happens on the doorbell camera, and then it has an abnormal LED? Such as firmware updates.
Best Regards
- Copy Link
- Report Inappropriate Content
The doorbell camera is flashing red and green.
Pressing the SYNC/RESET button for 5 seconds makes it briefly flash just red, but then it goes back to red and green.
I've installed (multiple) firmware updates to the Hub, as prompted by the mobile app, but I've not connected to the doorbell yet.
- Copy Link
- Report Inappropriate Content
Hi,
The LED status on the doorbell is correct after resetting, please refer to the below setup video to configure the Tapo D230 for a try, and move the doorbell close to the hub when configuring it.
How to Set Up Your Tapo Video Doorbell Camera Kit (Tapo D230S1)?
If you fail to connect the doorbell to the hub, please let me know which step you are getting stuck on, what error message appears, and what LED status on the doorbell.
Best Regards
- Copy Link
- Report Inappropriate Content
@Solla-topee please help, mine is doing the same thing. My app can see both the hub and the doorbell, but the doorbell doesn't connect to the hub. This setup worked ok for several months, and then the doorbell stopped responding. I have tried
- Copy Link
- Report Inappropriate Content
Hi,
Please try the following steps to troubleshoot.
1. Please ensure the hub Tapo H200 is configured successfully and working. Let me know the LED status on the hub.
Please try the instructions below if the hub can't be configured successfully.
Troubleshooting: What to do If Fail to Configure Tapo H200 Hub
2. If the hub is working, try to factory reset the doorbell camera. Generally, the camera will have a flashing red and green light after reset.
3. Try to set up the doorbell camera, and let me know which step you are getting stuck on if fail to set it up and what error message appears.
How to Set Up Your Tapo Video Doorbell Camera Kit (Tapo D230S1)?
You can check if the following instructions will help.
What can I do if the battery-powered cameras fail to pair with the Tapo H200?
Best Regard
- Copy Link
- Report Inappropriate Content
@Customer0 Hi, I had my doorbell successully set up for about 2 weeks now.
I had to re set my wifi box as the TV was frozen, which meant I had to reset the hub and doorbell. However, this time the doorbell is not connecting to the hub. The battery is fully charged. The hub is set up and ready to pair.
I put the battery into the doorbell. The LED flashes just red.
I tried to sync/battery reset, it stayed flashing just red.
I pressed the synce button for 1 second, it turns to flashing just green for a few seconds and then turns to just red again.
I have the doorbell right beside the hub and have tried everything mentioned in this thread.
It is not flashing red/green, it's either just flashing red for the majority, or a short time just green, when i press the sync button.
The hub is ready to pair as it has been reset.
Help!
- Copy Link
- Report Inappropriate Content
Hi
If the doorbell's LED flashes red slowly, it means the doorbell is offline and has not been reset successfully.
1. Please go to the Tapo app>Home tab and delete/remove the doorbell even if it displays offline status on the app.
2. After powering on the doorbell, please hold the SYNC/RESET button for 10 seconds to factory reset it, and check if the LED on the doorbell will be flashing red and green.
Best Regards
- Copy Link
- Report Inappropriate Content
@Solla-topee I have followed the set up steps but the doorbell is not linking to hub when I try to reset the doorbell by pressing the "reset" 10.sec the led.is blinking red continuously without stopping . I lost.my patience and I followed the set up accordingly .
- Copy Link
- Report Inappropriate Content
Hi,
Is your doorbell model number Tapo D230? Did it work before?
Does the doorbell's status LED change when you press the reset button?
Best Regards
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2325
Replies: 9
Voters 0
No one has voted for it yet.