Beta Software [Closed] Public Beta for Archer AX55 V1 Supports EasyMesh Ethernet Backhaul, DoH&DoT, ECO Mode etc.
Jan. 31st 2024 Update:
The trial period for the beta firmware has ended, and we will continue to address the ongoing issues.
Please keep an eye out for the official firmware release. If you encounter any new problems, please Start a New Thread to provide feedback.
Hello Everyone,
We're thrilled to announce the release of public beta firmware for Archer AX55 V1. This firmware update introduces several exciting new functions and improvements to enhance your experience including Ethernet Backhaul, EasyMesh in AP mode, Satellite Router Management, DoH&DoT, ECO Mode, etc. We encourage you to try out this beta firmware and take advantage of the following features. Your feedback and suggestions are greatly appreciated.
Download Link:
Archer_AX55_V1_1.2.6 Build_20231130
Notes:
1. This is a beta firmware and different from the official 1.2.6 version official firmware, please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding
2. This public beta firmware for Archer AX55 V1 can be applied to all versions (EU/US/JP/TW/etc.).
Modifications of 1.2.6 Build 20231130 compared to previous beta firmware
1. Improved client type identification accuracy
2. Added quick setup for third-party VPN including Surfshark and NordVPN in VPN Client feature
Here are the related FAQ:
How to Install Surfshark VPN on TP-Link Wireless Routers
How to Install NordVPN on TP-Link Wireless Routers
3. Added new HomeShield parental control features including Blocked Apps, App Time Limits, Always Allowed Apps etc.
The above two modifications are the same as this thread: Public Beta Release for Archer AX55 V1 to Enhance Its Ability to Recognize Client Devices
4. Added new functions to Tether App: EasyMesh, OpenVPN Server/Client, Eco Mode, Wireless Schedule, Guest Portal Network
Note: please use the new Tether App to experience those new features: New UI for 11AX Routers on Tether App 4.3 version is Ready for Trial
5. Added EasyMesh Backhaul Steering and AP Bind (Preferred WiFi Uplink AP)
Enabling Backhual Steering allows the satellite devices to flexibly connect to different mesh nodes based on their load status, optimizing your EasyMesh network performance.
Preferred WiFi Uplink AP: by default, it is set to Auto, when there are more than two mesh nodes in the same EasyMesh network and wireless backhaul is used, you could select a preferred AP for the satellite device, the preferred AP can be either the main router or another satellite device.
Improvements and Modifications of previous beta firmware 1.2.6 Build 20231106
New Features and Optimizations of EasyMesh:
1. Added Ethernet Backhaul.
2. Added EasyMesh feature in AP mode.
3. Enhanced EasyMesh Satellite Router Management via satellite router web interface.
4. Added EasyMesh Network Topology to gain a clear understanding of your EasyMesh network's structure.
More New Features
5. Added DoT and DoH features on Advanced->Network->Internet page, which supports customizing DNS Server as well.
6. Added ECO mode on Advanced->System->ECO Mode page.
When working in Power-Saving Mode or Ultra Power-Saving Mode, your router will reduce the power consumption to save power, please note that your network speed and coverage will be reduced as well.
7. Enhanced Wi-Fi Schedule to enjoy more flexibility by setting separate schedules for 2.4GHz and 5GHz Wi-Fi bands.
8. Added isolation of Guest Network and Main Network in AP mode.
9. Added Language options on the top of the web interface.
10. Added OpenVPN Server TAP Mode. Introducing TAP Mode in OpenVPN Server for AX55 V1 Router
Note: It requires your OpenVPN Client supporting TAP Mode as well, or you will not be able to connect the VPN Server successfully
10. Added User Experience Improvement Program (UEIP).
Participate in our UEIP during the Quick Setup process, or enable/disable it later on the Advanced->System->About page. Your feedback will help us enhance the product.
We invite you to download and install the beta firmware to explore these incredible new features. If you encounter any issues or have any suggestions, please leave your comments. Your input is invaluable to us.
Thank you for your continued support and for being part of our community.
Related Articles
Product List of Wi-Fi Routers that Support EasyMesh Ethernet Backhaul
What is EasyMesh and how does it work with TP-Link routers and extenders?
How to Build an Ethernet Backhaul Using Two EasyMesh Routers
What is DoH and How to use it on TP-Link Wi-Fi Routers?
Product List of Wi-Fi Routers that Support DoH
Introducing TAP Mode in OpenVPN Server for AX55 V1 Router
New UI for 11AX Routers on Tether App 4.3 version is Ready for Trial
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hello @Sunshine
Any possibility there is a beta firmware for the AX55 Pro?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
My apologies for somehow missing your post #87 from last Thursday.
Back on the static IP in AP mode issue, yes the problem still exists. Since then I rebooted the router back to Wireless Router mode for some more tests. After testing, the AX55 was once again rebooted in the AP mode. The front panel internet LED is orange but the iMac (on which I am writing this) is connected (via cable) just fine. Here are the screenshots from the AX55 AP:
The main AX55 is operating in Wireless Router mode and the AX55 AP is directly connected to the main router with a CAT6 ethernet cable. The main router’s firmware is version 1.2.3 Build 20230603 rel.46473(4555). Here are some screenshots:
Back on the client list issue, I will do some more testing tomorrow and provide you the results. I can say that In the prior tests, neither IP & MAC Binding or Access Control were enabled.
- Copy Link
- Report Inappropriate Content
uKER wrote
@Sunshine Appreciated! Just see to take out the part about it only happening over wired.
I was thinking as I went and later on figured that the PC was the only one being turned off and re-negotiating the DHCP, and forgot to delete that.
Hi, we are trying to locate the official 1.2.5 firmware issue now, and would like to forward your case to our senior engineer for debugging via remote session, if it is convenient for you, please let me know.
Looking forward to your reply.
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for the valuable information.
We have reported the issue to the support engineers, they will likely reach out to you via email to continue to troubleshoot your issue. Please check your email box and confirm.
- Copy Link
- Report Inappropriate Content
Sunshine wrote
Hi, we are trying to locate the official 1.2.5 firmware issue now, and would like to forward your case to our senior engineer for debugging via remote session, if it is convenient for you, please let me know.
Looking forward to your reply.
@Sunshine I'm totally up for it.
Let me know what I need to do.
- Copy Link
- Report Inappropriate Content
seiren wrote
@Sunshine I noticed that with a cold reboot of the router, all of my DHCP address reservations are disabled. I always need to manually enable every reserved address one by one. Is this normal behavior? This has been an issue since the last stable firmware and I'm using the latest beta right now..
Hi, we are unable to reproduce the issue on our end, may I know if the problem still exists on your router now?
If so, I would lilke to forward your case to senior engineers for debugging via remote session, please let us know if it is convenient for you.
- Copy Link
- Report Inappropriate Content
Hi, thanks a lot for the cooperation.
I've forwarded your case to the TP-Link support engineers who will contact you with your registered email address later. Please pay attention to your email box for follow-up.
- Copy Link
- Report Inappropriate Content
Following up to yesterday's post...
Clients List Testing Results
The device tested was an Archer AX55(EU) Version 1 router using beta firmware version 1.2.6 Build 20231106 rel.45124(4555). The client devices used were an iMac computer and an HP laptop computer.
1. AX55 in Access Point mode:
The AX55 WAN port was connected to a LAN port on the main router (also an AX55 but with the current firmware release) via a Cat6A ethernet cable. The iMac computer was used to connect remotely to the AX55 AP and monitor the clients list.
When the laptop computer was connected to one of the AX55 AP LAN ports, the clients list updated properly after a very brief interval. After disconnecting the laptop, the clients list again updated properly after less than 30 seconds.
The laptop was then connected via Wi-Fi, first using the 2.4 GHz network and then the 5 GHz network. The connections and the disconnects were each updated correctly on the clients list.
Therefore, it can be concluded that the clients list does update properly in the access point mode of the AX55.
2. AX55 in Wireless Router mode:
Using the same physical connections as before, the iMac computer was used to connect remotely to the AX55 under test and monitor the clients list.
When the laptop computer was connected to one of the AX55 LAN ports, the clients list updated properly. After disconnecting the laptop, the clients list did not update and after 10 minutes was still shown as connected.
The laptop was then connected using a 2.4 GHz Wi-Fi connection. The clients list then updated, reflecting the new wireless connection. However, after disconnecting and again after 10 minutes, the clients list still shows the laptop as connected.
The 5 GHz connection was tested with the same results.
Therefore, it can be concluded that the clients list does not update properly after a device disconnects when the AX55 is operating in the wireless router mode.
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for the detailed information, I've forwarded your case and the details to our senior engineer, and you could continue debugging the issue with them via email especially the static IP issue in AP mode.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 9
Views: 65138
Replies: 303
Voters 6
