Beta Software Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN
Hey Everyone,
We’re excited to introduce a new firmware update for the Deco X50/X55_V1.30/V1.33, packed with powerful new features and enhancements designed to elevate your Deco Mesh Home Networking experience.
This Article Applies to:
Deco X50(US/KR) / Deco X55(US/CA)_V1.30/V1.33
Modifications and Enhancements:
New Features
- Supported Channel Selection.
- Supported Internet Backup via Hotspot Backup and Hybrid-Mesh Backup Mode.
- Added DoH/DoT under Deco APP>More>Advanced.
- Supported 20MHz/40MHz automatic bandwidth selection to enhanced 2.4GHz WiFi performance.
- Supported WireGuard VPN Server/Client.
- Supported built-in easy configuration of NordVPN/Surfshark VPN.
***In compliance with local regulations, the Third-party VPN feature may be restricted to specific regions.
- Added client speed limit under clients' detailed setting page.
- Supported Fixing the WAN port under Deco APP>More>Advanced>WAN Port.
- Added Scene Priority under QOS.
- Added Client MAC Identification to improve the accuracy of device detection.
- Added Firmware Auto Update.
- Supported Matter
- Advanced Parental Control subscription added APP block/App Time Limits feature, which supports 2000+ applications.
- Added Camera Security
- Added Whitelist/ Wi-Fi Access Control
- Added notification for Ethernet connection speed.
- Supported Captive Portal for Guest Network
Enhancements
- Optimized the collaboration with Tapo smart devices.
- Updated HomeShield Parental Control service.
- Improved network stability and system security.
Firmware Download Link
Deco X50/X55_V1.30/V1.33 |
1.3.1_build_20251122_Beta |
Update Notice:
- Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
- Please make sure the Deco APP is up-to-date.
- This firmware can’t be degraded directly to the previous 1.2.10 version.
- How to manually update the firmware via web UI.
As always, we value your feedback. If you happen to encounter any concerns during or after the firmware upgrade, please feel free to comment below with the following information. Your input helps us continue to improve and provide the best possible products and support.
- Provide a detailed network layout, including how the devices are connected.
- Include a detailed description of the issue and as much information as possible regarding the specific conditions that seem to trigger the behavior.
Thank you for your continued support and for being part of our community.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I am facing a strange Wi-Fi issue. My router is on the 3rd floor, and I can use the internet from the ground floor without any problem. But when I move just 6 feet away from the router with 2 walls in between on the 3rd floor, my device shows Wi-Fi connected but there is no internet access. Near the router, everything works fine, but as soon as I move a short distance away, websites and apps stop loading even though it still shows connected.
- Copy Link
- Report Inappropriate Content
No acesspoint mode router mode. Range & performance drop issues without solve official version release?
- Copy Link
- Report Inappropriate Content
@David-TP, these features should also be implemented on Deco X60 V4.20.
Separate 2.4 & 5Ghz network, Channel selection, DoH/DoT, etc
- Copy Link
- Report Inappropriate Content
Hi, is there any specific reason that you used Deco M5 instead of Deco X50 working as the main Deco?
I think the 2.4GHz was on 40MHz when the speed throughput was 150 Mbps. Now the 2.4Ghz is on 20MHz.You could consider setting the Deco X50 as the main Deco so that you can manually change the channel/channel width.
Swapping the roles could help check if Deco X50_V1.3_1.3.1 could receive an IPV6 LAN address when it is the main Deco.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Deco M5 only for home Care. & Also for WiFi range. Still DECO M5 range much better than Deco X50.
Before update Deco X50 1.3*** everything working fine . That's why I want to downgrade firmware. So please if possible then I should use 1.2*** version firmware.
- Copy Link
- Report Inappropriate Content
Hi, thanks for the update.
You can refer to this link to run a firmware recovery on the Deco X50_V1.3, then upload the 1.2.10 to the web interface:
How to use firmware recovery on Deco
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 4
Views: 4358
Replies: 86
Voters 0
No one has voted for it yet.