Tapo c520ws not returning to it's default position after motion tracking
Tapo c520ws not returning to it's default position after motion tracking
Unfortunately both of my Tapo c520ws camera's do not return to its original position after motion tracking.
What I did to try to solve it:
- disabled motion tracking, reboot the camera, set the camera to the desired position, enabled motion tracking
- pan/tilt correction
- set detection zones, remove detection zones
- changed default position
What else can I do? Reading om the forum the problem occurs on almost all camera's.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Unfortunately the issue is not resolved. It is much improved, but still it does not always return to its original position.
In fact, in one day it first switched from its original position (below the red line) to another position which it seems to keep as its new original position. Later that day, it switched from that position to again another position.
- Copy Link
- Report Inappropriate Content
Another user with the same problem here: the camera "new" default position has become the last position a detection was made, far away from the intended default position (an entrance door in my case). It's a pity for an otherwise excellent camera.
- Copy Link
- Report Inappropriate Content
Hi,
You can try the following suggestions:
1. Update the Tapo app to the latest one.
2. Disable the Auto Tracking feature, pan & tilt the camera to the default position you want, and enable the Auto Tracking feature.
3. Go to the Smart Action > Automation page, and remove the entries that will pan & tilt the camera.
4. Test if the camera will work fine.
Best Regards
- Copy Link
- Report Inappropriate Content
Hi,
You can refer to the tips in the post here.
Best Regards
- Copy Link
- Report Inappropriate Content
Following your suggestions:
1. Update the Tapo app to the latest one.
Was already up to date.
2. Disable the Auto Tracking feature, pan & tilt the camera to the default position you want, and enable the Auto Tracking feature.
Did all this.
3. Go to the Smart Action > Automation page, and remove the entries that will pan & tilt the camera.
I didn't set any pan & tilt entry in Automation.
4. Test if the camera will work fine.
At the end of the detection, I disabled the alarm and switched the camera to privacy mode: the camera didn't return to the default position. (By the way, when I switched the privacy mode off, the camera triggered the alarm even if Alarm was set to OFF.)
I don't know if it helps, but once when after the detection I set the alarm off, the camera briefly showed the red lamp, then started to blink green and orange and after a few seconds turned stable green, without me doing anything. (The Wi-Fi signal in my home is excellent.)
- Copy Link
- Report Inappropriate Content
Hi,
We have firmware that may solve the issue, please send me(@Solla-topee) "Forum ID 714404+ Tapo C520WS's MAC address" via a private message if you want to try the firmware.
Before the Upgrade:
(1) Please be sure you have read the Beta Test Agreement before upgrading the Pre-release firmware!
(2) How to update the firmware of the Tapo devices on the Tapo App App
Best Regards
- Copy Link
- Report Inappropriate Content
1. Update the Tapo app to the latest one.
- Done
2. Disable the Auto Tracking feature, pan & tilt the camera to the default position you want, and enable the Auto Tracking feature.
- Done, this is standard procedure for me
3. Go to the Smart Action > Automation page, and remove the entries that will pan & tilt the camera.
- no automations used at all
4. Test if the camera will work fine
- issue is still the same
You already received my Mac Adrresses before. Please feel free to push mew Beta firmware to the camere's.
- Copy Link
- Report Inappropriate Content
Hi,
I can't find your camera's MAC address, would you please send it to me(@Solla-topee) again via a private message in the format "Forum 714404 + C520WS's MAC address"?
Thanks!
Best Regards
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 445
Replies: 18
Voters 0
No one has voted for it yet.