Home

Forums

Stories

Knowledge Base

Smart Home Community > All Threads > Having troubles trying to upgrade NC450 camera's firmware.

< All Threads

Having troubles trying to upgrade NC450 camera's firmware.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Having troubles trying to upgrade NC450 camera's firmware.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Blumed

2024-03-19 07:12:18 - last edited 2024-03-28 03:32:43

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2024-03-19

Having troubles trying to upgrade NC450 camera's firmware.

2024-03-19 07:12:18 - last edited 2024-03-28 03:32:43

Tags: #Firmware #Installation

Model: NC450

Hardware Version: V2

Firmware Version: NC450_v1.5.0_181022

Unable to setup NC450 after firmware upgrade and frequent restarts and disconnections, followed the instructions given in this thread but I can't seem to access the default access 192.168.0.10 for the camera even after following all the steps. Every time the browser just displays "This site can't be reached" or "Connection timed out", please help.

1 Accepted Solution

Solla-topee

2024-03-20 07:00:50 - last edited 2024-03-28 03:32:43

Posts: 13668

Helpful: 2360

Solutions: 2035

Stories: 8

Registered: 2020-05-19

Re:Having troubles trying to upgrade NC450 camera's firmware.-Solution

2024-03-20 07:00:50 - last edited 2024-03-28 03:32:43

@Blumed

Hi,
You can refer to the following steps to have a try.
1. With the camera powered on, press and hold the WPS/Reset button (for more than 5 seconds) until the System LED turns off. Then release the button and wait for the camera to reset to its factory default settings.

2. If you need to configure the camera, please refer to the link below to have a try.
How to set up cloud camera with tpCamera APP?

3. Refer to the instructions below to log in to the camera's web UI if needed.
How to log in to the cloud camera’s Web Interface?

If you fail to configure the camera and can't log in to the camera's web UI, you can contact your retailer or local support to check if the camera is under warranty.

Best Regards

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

Recommended Solution

1 Reply

Solla-topee

2024-03-20 07:00:50 - last edited 2024-03-28 03:32:43

Posts: 13668

Helpful: 2360

Solutions: 2035

Stories: 8

Registered: 2020-05-19

Re:Having troubles trying to upgrade NC450 camera's firmware.-Solution

2024-03-20 07:00:50 - last edited 2024-03-28 03:32:43

@Blumed

2. If you need to configure the camera, please refer to the link below to have a try.
How to set up cloud camera with tpCamera APP?

3. Refer to the instructions below to log in to the camera's web UI if needed.
How to log in to the cloud camera’s Web Interface?

If you fail to configure the camera and can't log in to the camera's web UI, you can contact your retailer or local support to check if the camera is under warranty.

Best Regards

>>Landscape Mode - Tapo App for Pad. >>Smart Action 2.0 Explore and meet the next level home automation. >>How to position my TP-Link camera for optimal performance.

Information

Helpful: 0

Replies: 1

Having troubles trying to upgrade NC450 camera's firmware.

Having troubles trying to upgrade NC450 camera's firmware.

Information

Voters 0

Tags